Manuals / Brands / Computer Equipment / Mouse / Asus / Computer Equipment / Mouse

Asus P2B ASUS PCI-L101Fast Ethernet Card, VI. ASUS LAN Card, Layout, LAN Card

1 64

Download 64 pages, 0 b

VI. ASUS LAN Card

ASUS PCI-L101 Fast Ethernet Card

LAN Card	Layout
ASUS	Parts /
VI.

LEDs

RJ45

LAN Activity

Output Signal

Intel

Chipset

Wake on LAN	ASUS
Wake on LAN
Output Signal		Motherboard type

Other

If you are using the ASUS PCI-L101 on an ASUS motherboard, leave the jumper on its defaut setting of “ASUS.” If you are using another brand of motherboard, set the jumper to “Other.” Connect the Wake on LAN (WOL) output signal to the motherboard’s WOL_CON in order to utilize the wake on LAN feature of the moth- erboard. Connect the LAN activity output signal (LAN_LED) to the system cabinet’s front panel LAN_LED in order to display the LAN data activity.

ASUS P2B User’s Manual

Contents

Page USER'S NOTICE Product Name: ASUS P2B Manual Revision: 1.03 E302 ASUSTeK COMPUTER INC Marketing Technical Support ASUS COMPUTER INTERNATIONAL ASUS COMPUTER GmbH CONTENTS I. INTRODUCTION II. FEATURES III. INSTALLATION IV. BIOS SOFTWARE V. DESKTOP MANAGEMENT VI. ASUS LAN Card FCC & DOC COMPLIANCE Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver How this Manual is Organized Item Checklist Features of the ASUS P2B Motherboard The ASUS P2B Motherboard Layout of the ASUS P2B Motherboard Jumpers Expansion Slots/Sockets Hardware Monitor Connectors Board Layout Installation Steps 1. Jumpers Jumper Settings III.INSTALLATION 3.CPU Bus Frequency (FS0, FS1, FS2) 4.CPU Core:BUS Frequency Multiple (BF0, BF1, BF2, BF3) Internal External Page Page 2.System Memory (DIMM) DIMM Memory Installation Procedures: 3.Central Processing Unit (CPU) Heatsinks Installing the Processor 3.Insert the SECC/SECC2/SEPP SECC with Pentium II only: 4.Secure the SECC/SECC2/SEPP ASUS Smart Thermal Solutions Recommended Heatsinks for Slot 1 Processors 4.Expansion Cards Expansion Card Installation Procedure Assigning IRQs for Expansion Cards Assigning DMA Channels for ISA Cards ISA Cards and Hardware Monitor 5. External Connectors 3.Parallel Port Connector (25-pinFemale) NOTE 7.Primary / Secondary IDE Connectors (Two 40-1pinIDE) 8.IDE Device Activity LED (2-pinIDELED) 9.Chassis / CPU / Power Supply Fan Connectors (3-pinFAN) do not place jumper caps over these pins 10.Chassis Intrusion Alarm Lead (4-1pin CHASIS) 11.IrDA-CompliantInfrared Module Connector (5-pinIR) 12.ATX Power Supply Connector (20-pinATXPWR) 13.Wake-on-LANConnector (3-pinWOL_CON) VII. ASUS LAN Card 14.SB-Link™Connector (6-1pin SBLINK) 15.SMBus Connector (5-1pin SMB) INSTALLATION 16.Message LED Lead (MSG.LED) 17.SMI Suspend Switch Lead (SMI) 18.ATX Power Switch / Soft Power Switch (PWR.SW) 19.Reset Switch Lead (RESET) 20.System Power LED (PWR LED) Power Connection Procedures Flash Memory Writer Utility Main Menu 2. Update BIOS Including Boot Block and ESCD Flash Memory Writer IV. BIOS Managing and Updating Your Motherboard’s BIOS 6. BIOS Setup Load Defaults Standard CMOS Setup Details of Standard CMOS Setup: Time Hard Disks For IDE hard disk drive setup, you can: •Use theAuto setting for detection during bootup •Enter the specifications yourself manually by using the “User” option Auto detection of hard disks on bootup Auto NOTE: SETUP Defaults are noted in parenthesis next to each function heading Drive A / Drive B (None) Floppy 3 Mode Support (Disabled) BIOS Features Setup Details of BIOS Features Setup BIOS BIOS CPU Level 1 Cache / CPU Level 2 Cache (Enabled) CPU Level 2 Cache ECC Check (Disabled) This function controls the ECC check capability in the CPU level 2 cache BIOS Update (Enabled) Security Option (System) Supervisor Password User Password System Setup Chipset Features Setup Details of Chipset Features Setup Graphics Aperture Size (64MB) Video Memory Cache Mode (UC) USWC PCI 2.1 Support (Enabled) Memory Hole At 15M–16M(Disabled) Onboard FDC Swap A & B (No Swap) Onboard Serial Port 1 (3F8H/IRQ4) Settings are and for the onboard serial connector Power Management Setup Details of Power Management Setup Video Off Method (DPMS OFF) DPMS OFF DPMS Reduce ON Blank Screen V/H SYNC+Blank, DPMS Standby PWR Up On Modem Act (Enabled) AC PWR Loss Restart (Disabled) Disabled Wake On LAN (Enabled) Automatic Power Up (Disabled) PNP and PCI Setup Details of PNP and PCI Setup DMA x Used By ISA (No/ICU) ISA MEM Block BASE (No/ICU) SYMBIOS SCSI BIOS (Auto) Auto USB IRQ (Enabled) Load BIOS Defaults Load Setup Defaults Supervisor Password and User Password IDE HDD Auto Detection Save & Exit Setup Exit Without Saving Desktop Management Interface (DMI) Introducing the ASUS DMI Configuration Utility System Requirements Using the ASUS DMI Configuration Utility Notes Save MIFD Load MIFD Load BIOS Defaults Using ASUS PCI-L101Fast Ethernet Card Features Software Driver Support Question and Answer