Thermo Products OHFA199DV5B manuals

Thermo Products OHFA199DV5B Operation Manual

78 pages3.27 Mb

OIL FIRED FURNACE
- INST ALLATION AND OPERATION M ANUAL WITH USERS INFO RM ATION SECTION
  - 6A. CODES AND CLEARANCES:
  - 7B. MAKE-UP AIR: Today's emphasis on home insulation increases the probability of inadequate air
  - 8 II. GENERAL INSTRUCTIONS - READ BE F ORE ST ART OF INSTALLATION
  - WARNING:
  - 9 A. CHIMNEY:
  - 102. PROPER CHIMNEY HEIGHT:
  - 3. PROPER VENT CONNECTOR PIPE/CHIMNEY CONNECTIO N:
  - 115. TIGHT JOINTS:
  - 6. TIGHT CLEAN-OUT DOORS AND CONNECTIONS:
  - 7. NO INTERCONNECTED CHIMNEY FLUES:
  - 8. FLUE PIPE CLEARANCES, SIZING AND TYPE:
  - 12REDUCTION OF CLEARANCES WI T H SPECIFIED FORMS OF PROTECTION:
  - 13B. VENTING:
  - CAUTION MUST BE TAKEN NOT TO EXCEED 90 ROTATION (OF THE FLUE ELBOW) .
  - ROTATION OF FRONT FLUE ELBOW:
  - 14C. DRAFT REGULATORS:
  - D. DUCT WORK/AIR CONDI TIONING:
  - Air flow Requirements and Sizing of Duct Work:
  - 18E. Air Filter Mounted Ex ternal to Furnace:
  - F. LIMIT POSITION AND LOCATION
  - 20TABLE 5: Installation location of the fan and limit control for each furnace
    - 21G. BURNER INS TALLATION:
    - 22H. BURNER SPECIFICATIONS AND APPLICATIONS:
    - 24MOUNTING THE 2-STAGE RIELLO BURNE R:
    - 25 I. OIL TANK AND PIPING:
    - 26J. OIL FILTER:
    - K. ELECTRICAL WIRIING:
    - 27Electronic Ai r Cl eaner (EAC) and Humidifier Installation:
    - 29Preferred method of adjustment:
    - 30 L. Blower Motor Speed S election:
      - 28
    - 31Heating Speed Set-ups
    - - 29
    - 32Heating Speed Set-ups
      - OH8FA119DV5
    - Furnace Motor Current
      - Draw (Amps / Watts) vs. External Static Pressure (in W.C)
    - - 35 32
      - NOTE: All information is approximate. Results will vary by installati o n .
      - 36 33
      - 34
      - OH8FA119D60
    - 37
      - Speed vs. color code for PSC Motor: Low = Red Med-Low = Blue Med-High = Yellow High = Black
    - 38 M. BLOWE R CONTROLLER INFORMATION FOR PSC MOTOR
    - 41
    - 43N. STARTUP PROCEDURES:
      - For You r Safety Read Before Operating:
    - Do not use this appliance if any part has been under water. Immediately call a qualified
    - 45COMBUSTION HEAD SETTING F OR 2-STAGE RIELLO BURNER:
    - 46TURN TO THE RIGHT : (SIGN + )
    - TURN TO THE LEFT: (SIGN - ) Figure 21
    - AIR DAMPER ADJUSTMENT:
    - 471st STAGE ADJUSTMENT:
    - 2nd STAGE ADJUSTMENT:
    - 48NOTICE: Minimum temperature rise is 50F.; maximum temperature rise is 80F.
    - k.
    - l. Check for the presence of oil leaks. Correct any oil leaks found.
    - m. Reassemble the burner compartment cover.
    - 3. Adjustm ent Of Heat Input Ra te:
    - 49NOTICE: It may be necessary to bleed air from the oil line before the burner can be fired.
    - 4. Setting Supply Air Temperature Rise:
    - 53IV. INS TALLER'S INSTRUCTIONS TO USER:
    - 54V. DEALER MAINTENANCE:
    - A. GENERAL INSPECTION:
    - WARNING: Shut off oil and disconnect power before continuing with this inspection.
    - 55B. HEAT EXCHANGER:
    - WARNING: A quali fied heating contractor must clean the heat exchanger.
    - C. HEAT EXCHANGER CLEANING INSTRUCTIO NS:
    - WARNING: THE HEAT EXCHANGER MUST BE CLEANED BY A QUALIFIED SERVICE PERSON.
    - 58Filter replacement:
    - G. EXTENDED APPLIANCE S HUTDOWN:
    - 61 VII. TROUBLESHOOTING:
    - PERSONNEL, AND NOT BY THE FURNACE OWNE R.
    - 62A. DIAGNOSTICS :
    - Diagnostic Features:
    - B. CAD CELL CHECKOUT PROCEDURE:
      - 71manua l ca refully before m aking tes ts. Reta in this form with furna ce.