Manuals
/
Brands
/
Laundry Appliance
/
Clothes Dryer
/
ADC
/
Laundry Appliance
/
Clothes Dryer
ADC
ML-82 service manual
Please, tick the box below to download manual:
Contents
Main
Retain This Manual In A Safe Place For Future Reference
Important
Page
Page
Table of Contents
Page
SECTION I
IMPORTANT INFORMATION
A. SAFETY PRECAUTIONS
Page
A. SPECIFICATIONS
SECTION II
SPECIFICATIONS/COMPONENT IDENTIFICATION
Steam
Gas
Page
B. COMPONENT IDENTIFICATION
Page
SECTION III
ROUTINE MAINTENANCE
A. CLEANING
B. ADJUSTMENTS
C. LUBRICATION
SECTION IV
DESCRIPTION OF PARTS
Page
Page
Page
M. REVERSING RELAY PANEL
SECTION V
SERVICING
INTRODUCTION
A. COMPUTER CONTROLS To Replace Computer Board
To Replace Keyboard Label Assembly
NOTE: DO NOT remove screws.
To Replace Microprocessor Temperature Sensor Probe
B. IGNITION CONTROLS To Remove Hot Surface Ignitor
To Remove Flame Sensor Probe
HSI Ignitor Flame Sensor Probe
To Replace Gas Valve (Refer to burner illustration on page 14)
To Replace Main Burner Orifices
To Test and Adjust Gas (Water Column) Pressure
To Convert Natural Gas to L.P. Gas
To Replace Burner Tubes
To Replace HSI Module
C. TO REPLACE BURNER HI-LIMIT THERMOSTAT (GAS MODELS ONLY)
To Replace Lint Compartment Hi-Heat Protector (225 F [107 C]) Thermostat
NOTE: DO NOT remove the screws.
D. SAIL SWITCH ASSEMBLY (GAS MODELS ONLY)
To Replace Sail Switch
To Adjust Sail Switch
E. FRONT PANEL and MAIN DOOR ASSEMBLIES To Replace Main Door Switch
To Replace Main Door Assembly
To Install New Main Door Glass
To Replace Front Panel
To Replace Main Door Hinge Block
Page
To Replace Piston
To Replace The Needle Valve
To Replace the 3-Way Micro Valve
To Replace Steam Coil
G. TUMBLER and BEARING ASSEMBLY
To Replace Tumbler Pulley (Reversing)
To Replace The Rear Tumbler Bearing
To Replace The Front Tumbler Bearing
H. IDLER SHAFT and BEARING ASSEMBLY
To Replace Idler Pulley
To Replace Idler Bearing
NOTE: Check tension and alignment of belts before operating dryer.
I. DRIVE PULLEY
NOTE: If rust has developed on the shaft use an emery cloth to polish the shaft.
NOTE: Check tension and alignment of belts before operating dryer.
J. TUMBLER (BASKET) Tumbler Alignment (Vertical)
NOTE: V-belt tension may need to be loosened.
Tumbler Alignment (Lateral)
To Replace The Tumbler And/Or Tumbler Support
IMPORTANT: When removing front panel assembly be careful not to damage door switch wires.
K. V-BELTS (REFER TO ILLUSTRATIONS IN SECTIONS I and K)
V-Belt Tension Adjustment-Tumbler To Idler
Page
SECTION VI
PHASE 6 OPL SYSTEM DIAGNOSTICS
A. DIAGNOSTIC (L.E.D. DISPLAY) FAILURE CODES
Page
B. L.E.D. (LIGHT EMITTING DIODE) DISPLAY INDICATORS
Page
Page
Page
Page
D. L.E.D. CODES
Page
SECTION VII
TROUBLESHOOTING
Page
Page
Page
Page
1. No Display Condition
2. Drive motor reverses but does not forward, blower motor runs
3. Drive motor works in forward mode but does not reverse, blower motor runs
4. Blower motor does not operate, drive motor runs
5. Lint Door Condition
6. Main Door Condition
7. No Heat drive and blower motors run, display reads normal (gas models).
8. Temp Sensor Fail Check
SECTION IX
TECHNICAL INFORMA TION
A. MOTOR PLATE (HIGH and LOW VOLTAGE)
Page
Page
IMPORTANT
C. COMPUTER LOGIC
SECTION X
SERVICE/PARTS INFORMA TION
A. SERVICE
B. PARTS
SECTION XI
WARRANTY INFORMATION
A. RETURNING WARRANTY CARD(S)
B. PARTS
C. RETURNING WARRANTY PARTS
Page
D. ML-82 TOOL LIST