ADC ML-82 specification

2.Dryer Rear View

Illus. No.

Description

1Heating Unit

21/8" Compressed Air Supply Inlet

	(behind Electric Service Relay Box for Steam Models Only)
3*	Electric Service Relay Box

4Tumbler Bearing Mount Assembly

5Idler Bearing Mount Assembly

6Basket (Drive) Motor Assembly (for Reversing Models Only)

7Blower Motor Assembly

8Dryer Exhaust

*Electric service connections for Gas Models and Steam Models are made in this box.

8

Image 12

ADC ML-82 service manual

Contents

ML-82 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Section SERVICE/PARTS Information Safety Precautions Important Information Standards SPECIFICATIONS/COMPONENT Identification Specifications Specifications MLG-82 Gas MLS-82 Steam Component Identification Page Routine Maintenance Cleaning Adjustments Lubrication Control Panel Assembly Door Switch AssemblyLint Drawer Lint Drawer Switch Description of Parts Basket and Support Assembly Temperature Sensor Bracket AssemblyTumbler Bearing Assembly Idler ARM Assembly DRIVE/FAN Mount AssemblyBlower Motor HSI HOT Surface Ignition Burner BOX Assembly Sail Switch AssemblyFront Panel Assembly Reversing Relay Panel Servicing Introduction To Replace Keyboard Label Assembly To Replace Microprocessor Temperature Sensor ProbeComputer Controls To Replace Computer Board Ignition Controls To Remove Hot Surface IgnitorTo Remove Flame Sensor Probe HSI Ignitor Flame Sensor Probe To Test and Adjust Gas Water Column Pressure To Replace Gas Valve Refer to burner illustration onTo Replace Main Burner Orifices To Convert Natural Gas to L.P. Gas To Replace Burner Tubes To Replace HSI ModuleTo Replace Burner HI-LIMIT Thermostat GAS Models only Sail Switch Assembly GAS Models only To Replace Sail Switch To Adjust Sail Switch To Replace Main Door Assembly To Install New Main Door Glass To Replace Front Panel To Replace Main Door Hinge Block Steam Controls Installation To Replace Steam Coil Damper System To Replace Piston To Replace The Needle ValveTo Replace the 3-Way Micro Valve To Replace Steam Coil Tumbler and Bearing Assembly To Replace Tumbler Pulley ReversingTo Replace The Rear Tumbler Bearing Idler Shaft and Bearing Assembly To Replace The Front Tumbler BearingTo Replace Idler Pulley To Replace Idler Bearing Drive Pulley Tumbler BasketTumbler Alignment Vertical Tumbler Alignment Lateral To Replace The Tumbler And/Or Tumbler Support Belt Tension Adjustment-Tumbler To Idler Belts Refer to Illustrations in Sections I and K Belt Tension Alignment Motor To Idler To Replace V-Belts Phase 6 OPL System Diagnostics Diagnostic L.E.D. Display Failure CodesPage E.D. Light Emitting Diode Display Indicators E.D. Display Indicator NumberPage FAN Blower Output L.E.D. light emitting diode Indicator AIR AIR JET Output L.E.D. Indicator OptionalHT1 Heat Output L.E.D. Indicator Fuse Main Fuse Input L.E.D. Indicator Lint Lint Door Input L.E.D. light emitting diode Indicator Main Main Door Input L.E.D. IndicatorDrum Tumbler HI-LIMIT Input L.E.D. Indicator Sail Sail Switch Input L.E.D. Indicator Power Supply Input L.E.D. Indicator E.D. Codes Fault Codes GAS Models only Power 24 VAC is not Evident AT GAS ValveGAS/ELECTRIC only BURNER/OVEN Open HI-LIMIT Circuit GAS only Ignition Attempt Failure Troubleshooting Computer will not accept keypad touchpad entries Drive motor runs, burner is on, but basket will not turn Dryer operates but is taking too long to dryThermal overload for drive motor is tripping Burner hi-limit safety thermostat is tripping Overload for impellor fan motor is tripping There is excessive vibration coming from the basket Electrical Troubleshooting No Display Condition Drive motor reverses but does not forward, blower motor runs Blower motor does not operate, drive motor runs Lint Door Condition Main Door Condition Temp Sensor Fail Check Technical Information Motor Plate High and LOW VoltageFor example Data Label Contact American Dryer Corporation Data Label Model Dryer American Gas Association, Canadian Gas Association Manual Reset HI-LIMIT Instructions Computer Logic SERVICE/PARTS Information ServiceParts Warranty Information Returning Warranty CardsReturning Warranty Parts Page ML-82 Tool List ADC 450404 1- 12/21/99-50