Patton electronic 4830 manual

Contents

Main SmartNode 4830 Series Analog VoIP Integrated Access Important Approval Getting Started Guide Page Summary Table of Contents Table of Contents Page Page Page List of Figures List of Tables About this guide Audience Structure Precautions Safety when working with electricity General observations The procedures described in this manual use the following text conventions: Typographical conventions used in this document Table 1. General conventions Convention Meaning Page SmartNode Model 4830 Series Overview Page SmartNode 4830 Series Detailed Description Figure 4. Examples of SN4830 Series rear panels (FXO only and combined FXS/FXO) Page Page Ports descriptions Reset button behavior SmartNode Model 4830 Series Overview 23 SmartNode 4830 Getting Started Guide 1 General information Figure 7. SmartNode 4830 Series front panels (FXS only) SmartNode Model 4830 Series Overview 24 SmartNode 4830 Getting Started Guide 1 General information ing on page 52. Note Some models within the 4830 Series differ from the above representa- tion as they come in a different shaped enclosure. Page Applications for SmartNode 4830 Series Multiservice carrier access over leased lines Page Chapter 3 Hardware installation Planning the installation Installation checklist Site log Network information Network Diagram IP related information Software tools Installing the VoIP IAD Mounting the VoIP IAD Connecting cables Installing an interface cable on the VoIP IADs FXS and FXO interface ports Page Installing the Ethernet cable Installing the serial WAN cable Page Page Page Page Connecting to external power source Figure 22. VoIP IAD front panel LEDs and Console port locations (SmartNode 4834 shown) Chapter 4 Getting started with the SmartNode Figure 23. Steps for setting up a new SmartNode 1 2 3 Note You can manually configure the SmartNode. You do not have to load a configuration file. 1. Congure IP address Power connection and default conguration Connect with the serial interface Login Changing the IP address 2. Connect the SmartNode to the network 3. Load conguration Bootloader Start Bootloader Start-up with factory conguration Load a new application image (SmartWare) via TFTP le_name base_address host Page Load a new application image (SmartWare) via the serial link Additional information Page Status LEDs 53 SmartNode 4830 Getting Started Guide 5 LEDs status and monitoring Status LEDs Figure 26. SmartNode 4830 Series front panels (FXS only) Page Page Chapter 6 Contacting Patton for assistance Contact information Patton support headquarters in the USA Alternate Patton support for Europe, Middle East, and Africa (EMEA) Warranty Service and Returned Merchandise Authorizations (RMAs) Warranty coverage Out-of-warranty service Returns for credit Return for credit policy RMA numbers Shipping instructions Appendix A Compliance information Compliance EMC compliance: Safety compliance: PSTN regulatory compliance: Radio and TV Interference (FCC Part 15) FCC Part 68 (ACTA) Statement (FXO ports) Industry Canada Notice (FXO ports) CE Notice Authorized European Representative Appendix B Specications DSP Voice connectivity Ethernet interface Sync serial interface (if applicable) T1/E1 interface (if applicable) ADSL Daughter Card (if applicable) G.SHDSL Daughter Card (if applicable) PPP and Frame-Relay support Voice processing (signaling dependent) Fax and modem support Voice signaling Voice routingsession product IP services Management Page Identication of the SmartNode devices via SNMP Appendix C Cabling Introduction 71 SmartNode 4830 Getting Started Guide C Cabling Enet 1 Console Serial console Serial Terminal Note A Patton Model 16F-561 RJ45 to DB-9 adapter is included with each SmartNode 4000 Series device VoIP Gateway Router ToIP Integrated Access Device SmartNode 4524 Ethernet 10Base-T and 100Base-T Figure 29. Ethernet straight-through Analog FXS Analog FXO T1/E1 DSL Appendix D Port pin-outs This section provides pin-out information for the ports of the SmartNode. Console port Conguration settings: 9600 bps, 8 bits, no parity, 1 stop bit, no ow control Ethernet 10Base-T and 100Base-T port Sync Serial Port V.35 Serial port X.21 Serial Port FXS port FXO port T1/E1 port ADSL/G.SHDSL port Page The factory conguration settings for SmartNode 4830 Series devices are as follows: