3M 9234 62-9234-9930-5, 9284 62-9284-9930-0, 9238 62-9238-9930-6, 9237 62-9237-9930-8 English

ENGLISH

General Information

Thumb pressure on the feeder pushes the adhesive stick into the heat block. The adhesive is melted by the heat block and pushed out through the tip. A fixed thermostat on the heat block maintains heat block temperature.

Start-Up and Operation

WARNING: USE ONLY 3M™ SCOTCH-WELD™ HOT MELT 2’’ x 5/8’’ LOW MELT ADHESIVE STICKS. OTHER ADHESIVES MAY CAUSE BACKMELT AND POSSIBLE INJURY. DO NOT USE NEAR HIGHLY FLAMMABLE MATERIALS.

1.Plug the 3M™ Scotch-Weld™ Hot Melt Applicator LT into a 120 VAC grounded receptacle. Allow 5 to 10 minutes for heat-up.

2.Pull the feeder back toward the rear of the applicator.

3.Snap a 3M Scotch-Weld Hot Melt Adhesive Stick (5/8’’ x 2’’) into the holder.

CAUTION: Do not force adhesive. Excessive force can damage the applicator and cause molten adhesive to flow out the rear.

4.Gently press the feeder forward and push the adhesive into the heat block. Melted adhesive will flow from the tip.

WARNING: TIP AND VALVE ARE HOT. KEEP TIP POINTED AWAY FROM BODY PARTS.

CAUTION: To avoid charring or plugging of the tip, extrude at least one adhesive stick every three hours that the applicator is turned on.

Shut-Down

1.Unplug the applicator.

2.Extrude one adhesive stick to cool down the applicator.

Preventive Maintenance

WARNING: TIP AND VALVE ARE HOT. WEAR HEAT- RESISTANT GLOVES WHEN CLEANING TIP. KEEP TIP POINTED AWAY FROM BODY PARTS.

To maintain proper operation, follow these steps.

1.Inspect nozzle tip daily. Make sure it is clean and clear of foreign matter.

2.Keep the adhesive clean and free of airborne contaminants.

Accessory Tips

The 3M Scotch-Weld Hot Melt Applicator LT comes equipped with a standard .093’’ tip. Contact your 3M Scotch-Weld Hot Melt Applicator distributor for additional tips.

Applicator must be at operating temperature. Hold the valve firmly with a 5/8’’ wrench and remove the tip with a 1/2’’ wrench. Mount the new tip and tighten.

Tip	Description
9725	Mini-extension/0.072’’ opening
9726	“T” tip/RSC carton closing
9727	“L” tip/FOL carton closing
9785	.070” Tapered aluminum extension
9940	.125’’ opening
9913	Two-hole spreader
9916	Three-hole spreader
9921	Standard .093’’ opening
9922	.063’’ Fluted tip

Changing Tips

WARNING: THE TIP AND VALVE ARE HOT. WEAR HEAT- RESISTANT GLOVES AND POINT TIP AWAY FROM BODY PARTS.

CAUTION: Do not overtighten. Overtightening damages threads.

Repair Parts Kit

9234	Valve Assembly Kit	3M Stock # 62-9234-9930-5
a. .093’’ tip
b. Valve Assembly
9237	Sleeve Kit	3M Stock # 62-9237-9930-8

a.Sleeve

b.Brass Flange (4)

9238 Feeder Kit 3M Stock # 62-9238-9930-6

a.Feeder

b.Metal Clip

9284	Power Cord Kit	3M Stock # 62-9284-9930-0
a. Power Cord (orange)
9262	Heater/Thermostat Kit	3M Stock # 62-9262-9930-6
a. Heater Assembly
b. Thermostat/TCO