crossover installation

bi-wiring / bi-amping

The 3-series allows conventional wiring, bi-wiring, or bi-amping using the supplied passive crossovers.

While conventional wiring will provide excellent sound, bi-wiring or bi-amping will further enhance the performance in no-compromise systems.

Bi-wiring uses a separate pair of speaker wires for the high frequency and low frequency signal between an amplifier channel and its associated crossover network. This gives you the option of choosing wire which may have slightly different sonic characteristics in order to optimize performance of each frequency range. Also, it reduces the overall wiring resistance between the crossover and amplifier, much like the use of larger gauge wire. This option provides the most benefit when the crossover network is mounted a long distance away from the amplifier. If the crossover is mounted close to the amplifier it is doubtful that there will be an appreciable difference between bi-wiring and conventional wiring.

Bi-amping is similar to bi-wiring except that it uses a separate amplifier channel for the high- frequency and low-frequency sections, instead of the single amplifier channel used in conventional and bi-wired connections. Bi-amping provides the additional advantages of reducing amplifier distortion and allowing the amplifier’s level controls to provide an additional level of fine-tuning not possible with the tweeter-level switch alone. In addition, at high power levels, a bi-amplified connection protects the tweeter from amplifier clipping, which is most likely to occur on channels driving the midrange, due to the higher energy levels of midrange signals. When bi-amping using the passive crossovers, the midrange low-pass filter and tweeter high-pass filter on the amplifier or external electronic crossover should be bypassed.

Carefully route the wires from the 3-series tweeter and woofer to the crossover mounting location. The crossover installation location should be reasonably accessible to allow easy connection of the wires, tweeter level adjustment and midrange contour selection. If the crossover must be mounted in an inaccessible location make the speaker wire connections and adjustments before final installation. Be sure the installation location has adequate clearance to allow the removal and replacement of the cover.

Mounting the crossover requires removing the top cover of it’s housing. Grasp the top cover at the front and back. Compress the cover slightly and lift it off the bottom of the housing. Mounting the crossover requires four holes in a rectangular pattern 2 13/16" x 4 1/4" on a flat surface. Use the provided template as a guide for drilling the mounting holes.

Align the mounting holes in the bottom half of the crossover unit with the holes you have drilled at the installation site. Pass the four #6 x 1 1/4" screws through the holes in the crossover unit, and tighten them until the assembly is firmly in place. As before, do not over-tighten; this is especially important if the mounting surface is not perfectly flat.

After all the connections and any necessary adjustments have been made snap the cover back in place.

connecting the system

Trim the speaker wire as needed. Strip about no more than 1/4" (6mm) of the insulation from the ends. Twist the exposed strands thoroughly to prevent any loose strands from causing a short circuit. If possible “tin” the wire with a soldering iron. The wires attach to a removable connector strip, in it’s attached position the screws face the bottom of the crossover.

Insert the prepared wire into the appropriate location (see diagram or refer to the crossover circuit board) in the connector strip and tighten the screws to secure the wires in place.

Note the polarity marking on the crossover circuit board.

12

9

Page 8 Page 10
Page 9
Image 9
a/d/s/ 335im, 336im, 334im manual Crossover installation, Bi-wiring / bi-amping, Connecting the system
Page 8 Page 10

336im, 334im, 335im specifications

The A/D/S series of amplifiers, specifically the models 335IM, 334IM, and 336IM, have made a significant mark in the world of audio technology, particularly in providing high-quality sound amplification for various applications. Each of these models integrates advanced features designed to enhance the listening experience, making them popular choices among audiophiles and professionals alike.

The A/D/S 335IM amplifier is renowned for its impressive power output, delivering robust performance while maintaining excellent audio quality. It typically features a Class A/B design, allowing it to provide warmth and clarity in sound. The 335IM is equipped with several inputs and outputs, making it versatile for both home theater setups and professional audio environments. Its built-in protection circuitry ensures reliability and prevents damage from overloads or overheating, extending the amplifier's lifespan.

Moving to the A/D/S 334IM, this model is often celebrated for its compact design and lightweight construction, making it easier to integrate into various audio setups. Despite its smaller form factor, the 334IM does not compromise on sound fidelity, delivering crisp highs and deep lows that satisfy even the most discerning listeners. It employs advanced signal processing technologies, which help in minimizing distortion and enhancing overall sound clarity.

Meanwhile, the A/D/S 336IM amplifier stands out with its advanced digital signal processing capabilities. With features like customizable audio settings and built-in equalization, the 336IM allows users to tailor their audio experience to their specific preferences. This model usually supports multiple audio formats, making it an excellent choice for modern home theater systems that rely on digital audio sources. Its efficient power management system ensures that audio performance remains optimal while reducing power consumption.

In summary, the A/D/S 335IM, 334IM, and 336IM amplifiers each bring unique strengths to the table. While the 335IM excels in power and reliability, the 334IM offers compactness without sacrificing sound quality. The 336IM, with its advanced digital features, caters to tech-savvy users looking for customization. Together, they exemplify A/D/S's commitment to delivering high-performance audio technology. These amplifiers represent a blend of quality, innovation, and user-friendly design, making them valuable assets for any audio setup.
Top Page Image Contents