FILLING THE WATER HEATER

Never use this water heater unless it is completely full of water. To prevent damage to the tank, the tank must be filled with water. Water must flow from the hot water faucet before turning “ON” gas to the water heater.

To fill the water heater with water:

1.Close the water heater drain valve by turning the handle to the right (clockwise). The drain valve is on the lower front of the water heater.

2.Open the cold water supply valve to the water heater.

NOTE: The cold water supply valve must be left open when the water heater is in use.

3.To insure complete filling of the tank, allow air to exit by opening the nearest hot water faucet. Allow water to run until a constant flow is obtained. This will let air out of the water heater and the piping.

4.Check all water piping and connections for leaks. Repair as needed.

GAS PIPING

Make sure the gas supplied is the same type listed on the model rating plate. The inlet gas pressure must not exceed 10.5” W.C. for natural gas and 13” W.C. for propane (L.P.) gas. The minimum inlet gas pressure shown on the rating plate is that which will permit firing at rated input.

If the gas control valve/thermostat is subjected to pressures exceeding 1/2 pound per square inch (3.5 kPa), the damage could result in a fire or explosion from leaking gas.

If the main gas line Shut-off serving all gas appliances is used, also turn “off” the gas at each appliance. Leave all gas appliances shut “off” until the water heater installation is complete.

A gas line of sufficient size must be run to the water heater. Consult the current edition of Natural Gas and Propane Installation Code (CAN/CSA B149.1) and your gas supplier concerning pipe size.

There must be:

•A readily accessible manual shut off valve in the gas supply line serving the water heater, and

•A drip leg (sediment trap) ahead of the gas control valve/ thermostat to help prevent dirt and foreign materials from entering the gas valve.

•A flexible gas connector or a ground joint union between the shut off valve and control valve to permit servicing of the unit.

Be sure to check all the gas piping for leaks before lighting the water heater. Use a soapy water solution, not a match or open flame. Rinse off soapy solution and wipe dry.

When installed at elevations above 4,500 feet (1371 m), input rating should be reduced at the rate of 4 percent for each additional 1,000 feet (305 m). This requires replacement of the burner orifice in accordance with the Natural Gas and Propane Installation Code (CAN/CSA B149.1-current edition). Contact your local gas supplier for further information.

Failure to replace the standard orifice with a high altitude orifice when installed could result in improper and inefficient operation of the appliance, producing carbon monoxide gas in excess of safe limits, which could result in serious injury or death. Contact your gas supplier for any specific changes which may be required in your area.

Use pipe joint compound or teflon tape marked as being resistant to the action of petroleum [Propane (L.P.)] gases.

The appliance and its gas connection must be leak tested before placing the appliance in operation.

The appliance and its individual Shut-off valve shall be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 pound per square inch (3.5 kPa). It shall be isolated from the gas supply piping system by closing its individual manual Shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 pound per square inch (3.5 kPa).

Connecting the gas piping to the gas control valve/thermostat of the water heater can be accomplished by either of the two methods shown in Figures 27, 28 and 29.

16

Page 15 Page 17
Page 16
Image 16
A.O. Smith FMD 40, FMD 50, FMD 30, 315795-000 MH instruction manual Filling the Water Heater, GAS Piping
Page 15 Page 17

FMD 40, FMD 50, 315795-000 MH, FMD 30 specifications

A.O. Smith is a renowned brand in the field of water heating solutions, offering a range of efficient and durable water heaters tailored to meet diverse consumer needs. Among its extensive lineup, the A.O. Smith FMD series showcases several commendable models, including the FMD 30, FMD 40, and FMD 50, each boasting unique features and advanced technologies.

The A.O. Smith FMD 30 is a compact water heater designed for smaller households or limited spaces. With a 30-gallon capacity, it is engineered to provide ample hot water for everyday needs such as bathing, washing dishes, and laundry. The heater employs advanced insulation technology, ensuring heat retention and energy efficiency. The thermostatic control system allows users to easily adjust the water temperature to their preference, ensuring comfort while promoting safety.

Moving to the A.O. Smith FMD 40, this model offers an increased capacity of 40 gallons, making it an ideal choice for medium-sized families. It incorporates A.O. Smith’s cutting-edge Durapower glass coating, which protects the tank from corrosion, ultimately extending its lifespan. The FMD 40 also features an enhanced heating element design that ensures rapid heating and consistent water temperature, making it perfect for bustling households.

The A.O. Smith FMD 50 takes things a step further, providing 50 gallons of hot water storage and designed for larger families or high-demand applications. This model integrates advanced technology features like a smart thermal control system that optimizes energy usage, ensuring that hot water is available when you need it without unnecessary power consumption. With robust construction materials, the FMD 50 is built to last, even in harsh conditions.

All models in the A.O. Smith FMD series prioritize user convenience. They come equipped with easy-to-read digital displays for monitoring temperature and status, along with built-in safety features such as automatic shut-off mechanisms. Installation is straightforward, and each unit adheres to energy efficiency standards, which help reduce utility bills while being environmentally friendly.

In summary, the A.O. Smith FMD series, including the FMD 30, FMD 40, and FMD 50, represents a commitment to quality and innovation. With their varying capacities and advanced technologies, these water heaters cater to a wide range of household needs, delivering reliable hot water solutions while maintaining energy efficiency and durability. Investing in an A.O. Smith FMD water heater not only guarantees comfort but also highlights a commitment to sustainability.
Top Page Image Contents