18
1. STOP!Read the safety information above on this label.
2. Setthe thermostat to lowest setting.
3. Thisappliance has a pilot that is lit by a spark gas ignition system. Do not try
to light the pilot by hand.
4. Removethe outer burner door.
5. Pushthe gas control knob down slightly and turn clockwise to "OFF" (see
Figure "A").
NOTE: Knob CANNOT be turned from "PILOT" to "OFF" unless it is pushed down
slightly. Do not force.
6. Wait ten (10) minutes to clear out any gas. Then smell for gas, including near
the floor. If you smell gas, STOP! Follow “B” in the safety information above
on this label. If you don’t smell gas, go to the next step.
7. Makesure the water heater is filled with water.
8. Turn gas control knob counterclockwise to "PILOT" (see Figure "A").
9. Depressthe gas control knob all the way in and IMMEDIATELY depress the
igniter button until you hear a loud click. Observe the pilot through the view
port. Do not release the gas control knob. Repeat immediately if pilot does not
light on the first try. If the pilot does not light by the fourth attempt with the
igniter, repeat steps 5-9. Continue to hold the button for about one (1) minute
after the pilot is lit. Release the gas control knob and it will pop back up. Pilot
should remain lit. If the pilot light goes out, repeat steps 5-9.
IMPORTANT:If the pilot will not stay lit after several tries, turn gas control knob
to "OFF" and call your service technician or gas supplier.
IMPORTANT:If the gas control knob does not pop up to its original position when
released, stop and immediately shut off the gas at the line valve or tank. Call your
service technician or gas supplier.
10.Turn gas control knob counter-clockwise to "ON" (see Figure "A").
11.Once the pilot flame is established replace the outer burner door.
12.Set thermostat to desired setting.
13.If the pilot will not stay lit after several tries, turn the gas control knob clock-
wise to"OFF" (see Figure "A"). If the appliance will not operate, follow the
instructions "To TurnOff Gas To Appliance" and call a qualified service tech-
nician or gas supplier.
1. Setthermostat to the lowest setting (PILOT LIGHTING).
2. Pushthe gas control knob down slightly and clockwise to the “OFF” position. Do not force.
WARNING:If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
A. This appliance has a pilot that is lit by a piezo-electric spark gas ignition system. Do not open the inner door of the
appliance and try to light the pilot by hand.
B. BEFORE OPERATING smell all around the appliance area for gas. Be sure to smell next to the floor because some
gases are heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Donot try to light any appliance.
• Donot touch any electric switch; do not use any phone in your building.
• Immediatelycall your gas supplier from a neighbour ’sphone. Follow the gas supplier ’sinstructions.
• Ifyou cannot reach your gas supplier, call fire department.
C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand,
don't try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system and any gas control which has been under water.
FOR YOUR SAFETY READ BEFORE OPERATING
LIGHTING AND OPERATING INSTRUCTIONS
TO TURN OFF GAS TO APPLIANCE
71731.1
Figure A
“OFF” Position
Gas Control Knob
Igniter
Button
Thermostat Dial
Gas Control
ELECTRODE
THERMO-
COUPLE
PILOT
Gas Control KnobTopView