Acoustic Energy A Ego 5 AEGOp5 Operation Delay Calibration, AEGOp5 Operation Pro Logic Mode

AEGOp5 Operation

AEGOp5 Operation

AEGOp5 Operation - Delay Calibration

Press the DELAY Button will display the current delay time for channel LS.

DOLBY DIGITAL CO

AEGOp5 Operation - Pro Logic Mode

Pressing the SL or SR button, switches the surround channels on and off. The LCD will display the following:

DOLBY DIGITAL CO

	Subwoofer	Centre
Front		Front
		Right
Left

DELAY SL 5 MS

Press the DELAY Button again will circle to next channel.

DOLBY	DIGITAL	CO
DELAY	SR 5	MS

Press the D TIME + or D TIME - button will increase or decrease the delay time for current channel.

DOLBY	DIGITAL	CO
DELAY	SR 6	MS

Pro Logic Mode

Your AEGOP5 will automatically switch to Pro Logic mode when it detects a Pro Logic signal. With other types of input signal, you can select the Dolby Pro Logic mode manually by pressing Pro Logic button on the remote. Repeatedly pressing the

Pro Logic Button will switch the Pro Logic mode in between the following modes; AUTO, ALL PCM, ENABLE and DISABLE.

input		power
mute		test
balance	delay	prologic
field	EQ on/off	EQ setup
preset 1	preset 2	preset 3
save1	preset 4	load
BassManager		Cen

SPK SUR ON

DOLBY DIGITAL CO

SPK SUR OFF

Pressing the SW button, switches the subwoofer on and off. The LCD will display the following:

DOLBY DIGITAL CO

SPK SW ON

Rear Left Rear Right

The recommended listening position is described below:

■ Centre channel speaker should be placed the same distance as the

left and right speakers from your listening position.

AEGOp5 Operation - Time Delay Adjustment on Surround Speakers

SL/SRSW

If a Pro Logic signal is detected, AEGOP5 will switch to Pro Logic mode automatically, and the display shows the following information:

DOLBY DIGITAL CO

PROLOGIC AUTO

DOLBY DIGITAL CO

SPK SW OFF

Bass Manager

Pressing the BASS MANAGER button enables you to select from three different settings of Bass; Bass Config.1, Bass Config.2 and Bass Config.3. These selections will feed the bass signal below 120Hz to different speakers as described below.

■ Rear left and right speakers should be placed behind your listening

position and above ear level.

■ If speaker placement is restricted due to the physical environment

of the room, delay calibration is sometimes necessary to achieve

the ideal listening environment.

■ If the centre speaker can only be placed nearer to you than the left

and right speakers, sound from the centre speaker will arrive

before the sound from the left and right speakers. The difference in

arrival time could may affect the sound quality and effect. Your

AEGOP5 allows you to adjust the speaker time delay to compensate

Delay Calibration

Press DELAY Button and repeat to select the length of delay time for SL/SR/C channels.

The delay range for SL/SR is 0 to 15 ms and 0 to 5 ms for centre.

Adjust the delay time on selected channel by pressing D TIME + or D TIME - on the remote control.

Surround Speaker Delay

mute		test
balance	delay	prologic
field	EQ on/off	EQ setup
preset 1	preset 2	preset 3
save1	preset 4	load
BassManager		Cen
SL/SR		SW
DRC	VOL	D Time

reset

If a stereo signal (either analog or digital) is detected, AEGOP5 will switch to stereo mode automatically. You can then convert the stereo mode to Pro Logic mode by pressing the Prologic button until you see the following on the display:

DOLBY DIGITAL CO

PROLOGIC ALL PCM

DOLBY DIGITAL CO

PROLOGIC ENABLE

If you want to convert Pro Logic or 2-channel Dolby Digital signal into Stereo mode, you can press the Prologic button until you see the

Bass Config.1

With this setting, the bass signal below 120Hz will be sent to the subwoofer; the LEDs on the front panel indicating SW will be red, and the LCD will show the following:

DOLBY DIGITAL CO

BASS CONFIG.1

Bass Config.2

With this setting, the bass signal below 120Hz will be sent to front left and right speakers and the subwoofer; the LEDs on the front panel indicating L/R/SW will be red, and the LCD will show the following

for this problem by increasing the delay time for the centre channel.

Thus sound from the centre, left and right speakers will reach you

at the same time. If your centre speaker is closer to your listening

position than the left and right speakers, press DELAY button

repeatedly until the centre channel is selected. To increase or

decrease the delay time, press D TIME + or D TIME - until the

desired delay is selected. The same procedure can be applied to

adjust the delay time of rear surround speakers if necessary.

Delay calibration for the rear surround

speakers may be necessary if the surround speakers are placed quite close to your listening position. To correct the delay this may cause, press the DELAY button repeatedly until SL or SR appear on the display. Increase the time delay of the surround speakers by pressing D TIME + until you are able to hear a 3D sound effect coming from surround speakers.

Press DELAY Button again to move to the next channel.

following on the display:

DOLBY DIGITAL CO

PROLOGIC DISABLE

AEGOp5 Operation - Speaker Mode with Bass Manager

information:

DOLBY DIGITAL CO

BASS CONFIG.2

Bass Config.3

With this setting, the bass signal below 120Hz will be sent to all the speakers; the LEDs on the front panel indicating L/R/SL/SR/SW channels will be red and the LCD will show the following information:

DOLBY DIGITAL CO

AEGOp5 Operation - Time Delay Adjustment on Centre Channel Speaker

Delay Calibration	mute		test
Press the DELAY button and repeat to	balance	delay	prologic
select the length of delay time for the
Rear Left (SL), Rear Right (SR) and	field	EQ on/off EQ setup
Centre(C) channels.	preset 1	preset 2	preset 3

DOLBY	DIGITAL		CO
DELAY	SL	5	MS
DOLBY	DIGITAL		CO
DELAY	SR	5	MS

Press D TIME + or D TIME - to increase or decrease the delay time for the selected channel.

DOLBY	DIGITAL	CO
DELAY	SR 6	MS

Speaker Mode with Bass Manager

The six LEDs on front panel of your AEGOP5 represent the six discrete audio channels (Left, Right, Centre, Rear Left, Rear Right and Sub). If a particular channel is active, the LED will light up in green. The LED will be red if that particular channel carries bass signal below 120Hz.

Speaker Mode

field	EQ on/off	EQ setup
preset 1	preset 2	preset 3
save1	preset 4	load
BassManager		Cen
SL/SR		SW
DRC	VOL	D Time

reset

BASS CONFIG.3

Bass Config. Off

With this setting, the bass signal below 120Hz will be sent to all the speakers; the LEDs on front panel of AEGOP5 indicating L/R/C/SL/SR/SW channels will be red and the LCD will show the following information:.

DOLBY DIGITAL CO

BASS CONFIG.OFF

	save1 preset 4	load
The delay range for SL/SR is 0 to 15	BassManager	Cen
ms and 0 to 5 ms for centre.
	SL/SR	SW
Adjust the delay time for the selected	VOL	D Time
	DRC
channel by pressing D TIME + or D	reset
TIME - on the remote control.

Pressing the CEN button, switches the centre channel on and off. The LCD will display the following:

DOLBY		DIGITAL	CO
SPK	C	ON
DOLBY		DIGITAL	CO
SPK	C	OFF

12 13