AEG 2.33 2 - page 55

55

screen 3.5 “Information“

In the screen “Information” you can check the UPs conﬁguration of the unit.

Conﬁguration and status of the unit:

• “single” single connection.

• “Parallel-single” parallel connection. Unit is in “single” state.

• “Parallel-Master” parallel connection. Unit is in “master” state.

• “Parallel-slave” parallel connection. Unit is in “slave” state.

Internal ﬁrmware versions of both Digital signal Processor (“DsP Ver:”) and

micro controller (“uC Ver:”).

UPs serial number, expressed with 10 characters.

service information in the basic settings should be used.

Contents

Main contents 2. Quality and standard guarantee .......................................................8 6. control panel and display description ............................................41 7. Maintenance, warranty and service ................................................71 1. IntroductIon 1.1. UsiNg this maNUal 1.1.1. symbols aNd coNvENtioNs UsEd Page 2. QuAlIty And stAndArd guArAntee 2.1. maNagEmENt dEclaratioN 2.2. staNdards 2.3. ENviroNmENtal ProtEctioN 3.1. viEws 3.1.1. viEws oF thE EqUiPmENt 3. PresentAtIon 11 *not available for Protect 2.33 2.0 Page 3.1.2 corrEsPoNdiNg lEgENds For thE EqUiPmENt viEws Page 3.2. strUctUrE 3.2.1. strUctUral schEma 3.3. oPEratiNg PriNciPlE 3.3.1. Normal oPEratioN 3.3.2. oPEratioN with maiNs FailUrE 3.3.3. oPEratioN with iNvErtEr Not activE 3.3.4. oPEratioN iN maNUal byPass 3.4. ParallEl oPEratioN Page 4. InstAllAtIon 4.1. imPortaNt saFEty iNstrUctioNs 4.1.1. battEry saFEty iNstrUctioNs 4.1.2. cabiNEt accEss Page 4.2. sEt UP aNd iNstallatioN 4.2.1. UNPackiNg aNd coNtENt chEckiNg 4.2.2. storagE 4.2.3. traNsPortatioN to sitE 4.2.4. locatioN 4.3. coNNEctioN 4.3.1. to thE maiNs coNNEctioN, tErmiNals (X1 to X4) Page 4.3.2. coNNEctioN oF thE oUtPUt, tErmiNals (X6 to X9) 4.3.3. UPs coNNEctioN to Each battEry Pack iN cabiNEt, tErmiNals (X11, X12, X23 aNd X47, X48, X49) 4.3.4. coNNEctioN maiN ProtEctivE EarthiNg tErmiNal ( ) aNd ProtEctivE Earth boNdiNg tErmiNal ( ) 4.3.5. iNtErFacE rElay coNtacts, coNNEctor (X32) 4.3.6. com-iNtErFacE rs232 aNd rs485, coNNEctor (X31) Page 4.3.7. EPo tErmiNals (X50) 4.3.8 ParallEl bUs coNNEctioN (X36) Page 5. oPerAtIon 5.1. start UP 5.1.1. coNtrol bEForE start UP 5.1.2. start UP ProcEdUrE PHASE REVERSE INPUT POWER CLOSE BATTERY SWITCH 5.2. comPlEtE UPs shUtdowN 5.3. EmErgENcy PowEr oFF (EPo) oPEratioN 5.4. byPass maNUal switch (maiNtENaNcE) 5.4.1. PriNciPlE oF oPEratioN 5.4.2. traNsFEr to maiNtENaNcE byPass 5.4.3. traNsFEr to Normal oPEratioN CLOSE BATTERY SWITCH 6. control PAnel And dIsPlAy descrIPtIon 6.1. coNtrol PaNEl Parts 6.1.1. toUch scrEEN 6.2. basic FUNctioNs oF kEyboard From syNoPtic Page Page Page Page 6.3.2. UPs statUs coNtrol (scrEEN mENU 1.0) Page 6.3.3. mEasUrEs lEvEl (scrEEN mENU 2.0) Page Page 6.3.4. sEttiNgs lEvEl (scrEEN mENU 3.0) Page screen 3.3: Page Page 6.3.5. alarms lEvEl (scrEEN mENU 4.0) Page Page Page Page Page Page Page Page Page Page Page Page 6.3.6. data loggEr lEvEl (scrEEN mENU 5.0) Page 7. MAIntenAnce, WArrAnty And serVIce 7.1. basic maiNtENaNcE gUidE 7.1.1. battEry FUsEs 7.1.2. battEriEs Page 8. AnneXes 8.1. gENEral tEchNical sPEciFicatioN Page tablE 6: EXtErNal battEry cabiNEt 8.2 saFEty iNstrUctioNs Page Page Page Protect 2.33 2.0