Starting Up and Temperature Regulation

Wash the inside of the appliance with lukewarm water with a little bicar- bonate of soda added (5ml to 0,5 litre of water). Do not use soap or deter- gent as the smell may linger. Dry the appliance thoroughly.

•When the refrigerator compartment door is opened, the internal lighting is switched on. The temperature control knob is located on the right hand side of the refrigerator compartment.

Setting “0”: Off.

Setting “1”: Highest temperature, (warmest setting).

Setting “6” (end-stop) :Lowest temperature, (coldest setting).

The exact setting should be chosen keeping in mind that the temperature inside the refrigerator depends on:

-the quantity of food stored

-how often the door is opened

The temperatures in the refrigerator compartment and freezer compart- ment cannot be independently regulated.

Positioning

This appliance should only be installed at a location where the ambient temperature corresponds to the climate classification indicated on the rat- ing plate, which is located on the inside left of the appliance.

The following table shows which ambient temperature is correct for each climate classification.

Climate classification

 

for an ambient temperature of

 

 

 

 

 

 

SN

 

+10 to +32 °C

 

 

 

N

 

+16 to +32 °C

 

 

 

The appliance should be located in a dry atmosphere, out of direct sunlight and away from continuous heat and extreme temperature, e.g. not next to a boiler or radiator, or in a very cold room e.g. an outhouse. If these tem- peratures are exceeded i.e. warmer or colder, then the appliance may not operate correctly.

For building-in and door reversal instructions please refer to the relevant instructions on the following pages.

If you want to freeze fresh food rapidly, select setting “6”, ensuring that the temperature in the refrigerator compartment does not drop below 0°C. You should reset the temperature control knob to setting “3” or “4”, if this does occur.

As soon as the fresh food placed in the freezer has frozen, return the tem- perature control knob to “3” or “4”.

Important!

High ambient temperatures (e.g. on hot summer days) and a cold setting on the temperature regulator (position"5" to "6") can cause the compressor to run continuously.

If this happens, turn the temperature regulator back to a warmer setting (position "3" to "4"). At this setting the compressor will be switched on and off as usual and automatic defrosting recommenced.

Your appliance needs air

For safety reasons, minimum ventila- tion must be as shown Fig.

Attention: keep ventilation openings clear of obstruction;

50 mm

min.

200 cm2

 

min.

 

200 cm2

D567

 

Reversing the door

The side the door opens can be changed from the right side (factory adjust- ment) to the left side, if the installation site requires.

Warning! When changing the side the door opens, the appliance must not be connected to the mains. Remove plug from the mains beforehand.

8

21

Page 7 Page 9
Page 8
Image 8
AEG C 7 18 40-4I Starting Up and Temperature Regulation, Positioning, Your appliance needs air, Reversing the door
Page 7 Page 9

C 7 18 40-4I specifications

The AEG C 7 18 40-4I is a versatile and high-performance power tool designed for both professional contractors and DIY enthusiasts. This multi-functional tool combines advanced technologies and thoughtful design features that make it a standout in the competitive market of power tools.

At its core, the AEG C 7 18 40-4I is a cordless reciprocating saw that offers remarkable flexibility. The tool is powered by a robust 18V lithium-ion battery, which not only provides longer runtime but also ensures consistent high performance throughout various cutting applications. This cordless design allows for greater mobility in tight spaces and outdoor environments where access to power outlets may be limited.

One of the main features of the AEG C 7 18 40-4I is its brushless motor technology. This feature increases efficiency and offers a longer lifespan compared to traditional brushed motors. The brushless motor generates less heat during operation, which contributes to prolonged battery life and reduces wear on the internal components, leading to a more reliable tool overall.

The AEG C 7 18 40-4I also boasts an adjustable speed setting, allowing users to tailor the cutting speed to match the material being worked on. This variable speed control is particularly beneficial for tackling different materials, whether it’s wood, metal, or plastic, providing the versatility needed for a wide range of tasks.

Another significant characteristic of the AEG C 7 18 40-4I is its tool-free blade change system. This innovative design allows for quick and efficient swapping of blades without the need for additional tools. This feature not only saves time but also enhances safety, as users can easily replace blades without coming into contact with sharp edges.

The ergonomic design of the AEG C 7 18 40-4I ensures user comfort during extended periods of use. Its lightweight build, combined with a soft-grip handle, provides superior control and reduces fatigue, making it an ideal choice for long projects.

The AEG C 7 18 40-4I is equipped with an integrated LED light, illuminating the work area and enhancing visibility in low-light conditions. This practical addition allows users to maintain precision and accuracy during their work.

In summary, the AEG C 7 18 40-4I is engineered for performance, durability, and user comfort. Its combination of brushless motor technology, variable speed control, tool-free blade changes, and ergonomic design makes it a powerful addition to any toolkit. Whether for construction professionals or home repair enthusiasts, the AEG C 7 18 40-4I delivers quality and reliability across a multitude of cutting applications.
Top Page Image Contents