What to do if…

 

 

 

 

 

 

 

 

17

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Problem

 

Possible cause

 

Solution

 

 

 

 

 

 

 

 

 

The appliance is noisy

 

The appliance is not supported

 

Check if the appliance stands sta-

 

 

 

properly

 

ble (all the four feet should be on

 

 

 

 

 

the floor)

 

 

 

 

 

 

 

 

 

 

The appliance does not

 

The appliance is switched off.

 

Switch on the appliance.

 

 

operate. The lamp does

 

 

 

 

 

 

 

not operate.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The mains plug is not connected

 

Connect the mains plug to the

 

 

 

to the mains socket correctly.

 

mains socket correctly.

 

 

 

 

 

 

 

 

 

 

 

The appliance has no power.

 

Connect a different electrical ap-

 

 

 

There is no voltage in the mains

 

pliance to the mains socket.

 

 

 

 

socket.

 

Contact a qualified electrician.

 

The lamp does not work.

 

The lamp is in stand-by.

 

Close and open the door.

 

 

 

 

 

 

 

 

 

 

 

The lamp is defective.

 

Refer to "Replacing the lamp".

 

 

 

 

 

 

 

 

 

The compressor operates

 

The temperature is not set cor-

 

Set a higher temperature.

 

 

continually.

 

rectly.

 

 

 

 

 

 

 

The door is not closed correctly.

 

Refer to "Closing the door".

 

 

 

 

 

 

 

 

 

 

 

The door has been opened too

 

Do not keep the door open longer

 

 

 

frequently.

 

than necessary.

 

 

 

 

 

 

 

 

 

 

 

The product temperature is too

 

Let the product temperature de-

 

 

 

high.

 

crease to room temperature be-

 

 

 

 

 

fore storage.

 

 

 

 

 

 

 

 

 

 

 

The room temperature is too

 

Decrease the room temperature.

 

 

 

high.

 

 

 

 

 

 

 

 

 

 

 

 

The compressor does not

 

This is normal, no error has oc-

 

The compressor starts after a pe-

 

start immediately after

 

curred.

 

riod of time.

 

 

pressing the COOLMATIC

 

 

 

 

 

 

 

switch, or after changing

 

 

 

 

 

 

 

the temperature.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Water flows on the rear

 

During the automatic defrosting

 

This is correct.

 

 

plate of the refrigerator.

 

process, frost defrosts on the

 

 

 

 

 

 

 

rear plate.

 

 

 

 

 

 

 

 

 

 

 

 

Temperature cannot be

 

COOLMATIC function switched

 

Switch off COOLMATIC manually,

 

set .

 

on.

 

or wait to set the temperature

 

 

 

 

 

until the function has reset auto-

 

 

 

 

 

matically. Refer to "COOLMATIC

 

 

 

 

 

function"..

 

 

 

 

 

 

 

 

 

The temperature in the

 

The temperature regulator is not

 

Set a higher/lower temperature.

 

appliance is too low/high.

 

set correctly.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The door is not closed correctly.

 

Refer to "Closing the door".

 

 

 

 

 

 

 

 

 

 

 

The product temperature is too

 

Let the product temperature de-

 

 

 

high.

 

crease to room temperature be-

 

 

 

 

 

fore storage.

 

 

 

 

 

 

 

 

 

Page 17
Image 17
AEG SKZ71800F0 user manual Problem Possible cause Solution