Inserting the Batteries, Low Battery Indicator | AGFA DC-530i

Inserting the Batteries

The camera is powered by two AA-size alkaline batteries or rechargeable NiMH (min. 1600 mAh / 1.2V) batteries.

1 Open the battery cover.

ySlide the battery cover in the direction indicated by the arrow.

2 Insert the batteries.

yInsert two AA-size batteries with the positive (+) and negative (-) poles matching the directions indicated inside the battery room.

3 Close the battery cover.

Low Battery Indicator

A low battery indicator appears on the LCD screen when the batteries are nearly exhausted. Batteries should be replaced promptly when the low battery indicator appears.

Caution

yBe sure to turn off the camera power before insert or remove batteries.

yUse only Alkaline or NiMH battery to power this camera. Use of any other type battery is not recommended.

yReplace all batteries at the same time. Never mix old and new batteries.

yRemove batteries if you will not be using them for a long time.

yThe camera body may feel warm after extended use. This is normal.

About Battery Type

After replacing the batteries, please check the Battery Type in the setup menu ( page 18).

5

Image 10

AGFA DC-530i user manual Inserting the Batteries, Low Battery Indicator, About Battery Type

Contents

DC-530i Precautions Extending battery life „ FCC Compliance and Advisory Contents Iii Making Connections Using This Menu Getting Started Scope of delivery Attaching the Wrist Strap Parts of the Camera Page About Battery Type Low Battery IndicatorInserting the Batteries Tips Inserting the Memory CardInsert the card About Camera Memory Setting the Display Language Setting the Display Language / Date & TimeSetting the Date & Time Apply the setting Using the LCD Monitor REC mode Play mode Dpof „ Play mode „ REC modeChanging the LCD Status Power Saving Function Turning the Power On and OffPress the Power button n again to turn the power off Basic Operation Selecting the REC mode Changing the ModeSwitching between REC mode and Play mode Set the camera to the REC mode Launch the mode palettePage REC menu Using the MenusChange the setting Select an item REC menu list Movie Setup menuOpen the Setup menu Press the Menu n button to close the menu Beep Setup menu listReset Off Computer / Printer PALNiMH Half press the shutter button to focus the image Basic RecordingRecording Still Images Take a picture Using the Q mode Resolution Values Setting the Resolution and QualityQuality Values Setting the Movie Size Recording Movie Clips Using the Zoom Function Using the Flash Using the Macro Double Using the Self-timer & Burst10 sec Burst Playing Back Audio Clips Recording and Playing VoicesRecording Audio Clips Press the shutter button again to end recording Open the Play menu Adding a Voice MemoRecording a Voice Memo Press the SET button to start recording for 30 seconds Setting the White Balance Setting the MeteringOther Recording Functions Setting the AEB Setting the ISOSetting the Exposure Setting the Highlight Setting the Photo Effect Setting the SharpnessSetting Date Stamp Playing Back Images Turn the power on, and set the camera to the Play modePlayback Press the four-way control or n Trim the image Magnifying & Trimming Still ImagesMagnify the image Save the image Button to show the selected image in full screen Change the slide show settingsViewing in Thumbnail Playing a Slide Show Playing the slide show Deleting FilesDeleting a Single File Select multiple images Deleting Multiple FilesPress or to select Select, and then press the SET button Delete images Protecting a Single File Play mode Open the menuProtecting All Files Protecting Multiple Files Press or to select Lock all, and then press the SET buttonPress the SET button to protect all images Thumbnail screen Open the menu Press the SET button to rotate the image Editing ImagesRotating Still Images Changing the Image Size Copying the Files Changing the Image with Effects S3 Press or to select Single, then press the SET button Setting the DpofPrint the date stamp out Choosing a Startup Image Making Connections Connecting the Camera to a TVDisplay on TV Using the Card Reader Connecting the Camera to a PCConnecting the Camera to a Computer with the USB Cable Double-click the Removable Disk icon to view its contents Software InstallationSystem Requirements Install VideoStudio 7 SE VCD Installing the SoftwareInstall Ulead Photo Explorer 8 SE Basic Utilities Drivers Follow the on-screen instructions to install the drivers Installing the Software DriverInstalling Ulead Photo Explorer 8 SE Basic Drive. The autorun menu appears Using the Software Installing VideoStudio 7 SE VCDUlead Photo Explorer 8 SE Basic Folder Structure AppendixAbout the Folder & File Name File Naming Troubleshooting Problem Cause Solution Mode Function Function Available List Still Capture Specifications Ntsc / PAL Customer care Manufactured by plawa-feinwerktechnik GmbH & Co. KG Declaration of Conformity