Air King 6C507B/9145B specifications Read and Save These Instructions, Description, Assembly

MODELO 6C507B/9145B

OPERATING INSTRUCTIONS & PARTS MANUAL

OPERACIÓN

1.Enganche el ventilador a una estructura que tenga un espesor de entre 3/4" y 1 1/8". Si engancha el ventilador a estructuras de mayor o menor espesor podría desestabilizarlo.

2.VELOCIDAD: La velocidad se controla mediante un conjuntor rotatorio de tres posiciones localizado en la parte trasera del alojamiento del motor.

3.AJUSTE DEL ÁNGULO: Afloje la perilla de debajo de la cabeza del ventilador. Incline la cabeza a la posición de flujo de aire deseada. Vuelva a apretar la perilla.

4.CORDÓN DE ALIMENTACIÓN ELÉCTRICA: Enchufe el cordón de alimentación eléctrica en un receptáculo de pared (120 volts CA, 60 Hz).

MANTENIMIENTO

ADVERTENCIA: DESCONECTE SIEMPRE EL CORDÓN ANTES DE MOVER O DAR SERVICIO AL VENTILADOR.

LIMPIEZA

Utilice un trapo suave, humedecido con una solución de jabón suave. Evite el uso de gasolina, bencina, diluyentes, solventes clorados, limpiadores ásperos, etc., ya que causarán daños al ventilador.

LUBRICACIÓN

Los cojinetes de precisión vienen sellados de fábrica de por vida y no requieren de lubricación adicional.

ALMACENAMIENTO

Cuando no esté en uso, guarde la unidad en un lugar limpio y seco.

ADVERTENCIA: PARA REDUCIR EL RIESGO DE INCENDIOS O DESCARGAS ELÉCTRICAS, NO USE ESTE VENTILADOR CON NINGÚN DISPOSITIVO DE CONTROL DE VELOCIDAD DE ESTADO SÓLIDO.

6" CLIP-ON AIR CIRCULATOR

MODEL 6C507B/9145B

READ AND SAVE THESE INSTRUCTIONS

READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.

PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH

INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

DESCRIPTION

The AirKing 6" (15.2 cm) Clip-On Air Circulator features whisper	5. Unplug power cord before installing or servicing the fan.
quiet operation, rotary switch control with adjustable vertical tilt	WARNING: DO NOT DEPEND UPON THE ON-OFF SWITCH
and 360° head pivot. The six inch (15.2 cm), 3-paddle fan blade	AS THE SOLE MEANS OF DISCONNECTING POWER WHEN
is powered by a permanently pre-lubricated motor.	INSTALLING OR SERVICING THE FAN. ALWAYS UNPLUG
	THE POWER CORD.

SPECIFICATIONS

Motor		120V, 50/60 Hz
Blade diameter		6" ( 15.2 cm)
Cord		6 ft. (1.8 m), 18/3
Speeds		2
Control		Rotary Switch
Approvals		UL listed. Close mesh fan guard meets
		OSHA requirements.
	MODEL	6C507B/9145B
	SPEED	HIGH	LOW
	CFM	566	488
	M3/s	.27	.23
	RPM	2460	2295
	Amps	0.19	0.15
	Watts	13	11
	dB A	37	34

6.This fan is intended for general use ONLY. It must NOT be used in potentially dangerous locations such as flammable, explosive, chemical-laden or wet atmospheres. DO NOT use fan in a window. Rain may create an electrical hazard.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID STATE SPEED CONTROL DEVICE.

ASSEMBLY

1.Remove T-Knob from Fan Head Assembly while being careful to retain the Hex Nut on the opposite side. ( Figure 1)

2.Insert the Fan Head Assembly into the Slot on the Clip Assem- bly.

3.Reinstall the T-Knob. Tighten securely.

2019

LISTA DE REPUESTOS

NO.	PARTE	DESCRIPCIÓN	CANT.	NO.	PARTE	DESCRIPCIÓN
REF	NO.			REF	NO.		CANT.
1	2011739	Ornamento	1	14	2091138	Tornillo de la cubierta trasera
2	2096065	Rejilla frontal	1
						del motor	2
3	2011754	Paletas	1
				15	2011724	Interruptor de mando	1
4	2090588	Abrazadera de las paletas	1
				16	2050099W	Cordón eléctrico	1
5	2090123	Tuerca hexagonal M4	2
				17	2011704A	Perilla de ajuste	1
6	2091156	Tuerca hexagonal 8-32	1
				18	2011397	Cuello	1
7	2011684	Alojamiento del motor y rejilla trasera	1
				19	2009102	Pata	2
8	2030078H	Conjunto del motor	1
				20	2091116	Tornillo HWH #8 x 5/8 Tipo 25	1
9	2090117	Arandela de bloqueo con dientes ext #8	1	21	2091149B	Resorte de las mordazas	1
10	2091119	Tornillo de tierra #6 x 3/8"	1
				22	2011377	Mordaza superior	1
11	2057062	Interruptor	1
				23	2011387	Mordaza inferior	1
12	2011764	Interruptor	1

GENERAL SAFETY INFORMATION

1.Make certain that the power source conforms to the electrical requirements of the fan.

2.The power cord is equipped with a three-prong grounded plug that must be inserted into a matching receptacle. Under no circumstances must the grounding prong be cut off the plug. Where a two-prong wall receptacle is encountered, it must be replaced with a properly grounded three-prong receptacle installed in accordance with the National Electrical Code (NEC) and all applicable local codes and ordinances. This work must be done only by a qualified electrician, using copper wire only.

WARNING: USE OF A THREE-PRONG TO TWO-PRONG ADAPTER IS NOT RECOMMENDED. IMPROPER CONNEC- TION MAY CREATE THE RISK OF ELECTROCUTION. USE OF SUCH ADAPTERS IS NOT PERMITTED IN CANADA.

3.Where possible, avoid the use of extension cords. If they must be used, minimize the risk of overheating by ensuring that they are UL listed and of the proper gage and length. Never use a single extension cord to operate more than one fan.

4.Do not insert fingers or foreign objects into the fan. Do not block or tamper with the fan in any manner while it is in operation.

Figure 1

4.WALLMOUNT USE: Install a Screw (#8 x 3/4" Wood Screw or equivalent...not supplied) in the wall and hang the Clip Assem- bly on the Screw. (Figure 2)

Figure 2

Rev. C (Color) 2/97 4 2085299A

Rev. C (Color) 2/97 1 2085299A