Contact your dealer if you desire more information about this important safety feature.

Should any unusual conditions be observed during your inspections, call an authorized service dealer immediately.

Return Air

All return air duct connections must be tight and sealed to unit cabinet. Supply and return air registers must be open when the unit is in operation. Obstructions must not be allowed to block airflow in or out of the registers.

Filters

Air filters are to be used with this heating/cooling unit. Filters are not factory supplied in the unit. However,

Minimum Required Surface Area

for Disposable Filters

Table 1

the return air compartment includes provisions that allow filters to be installed within the unit. Otherwise, a filter must be installed in the duct work by the installer. Filters must always be installed ahead of the evaporator coil and must be kept clean or replaced. Dirty filters will reduce the airflow of the unit. Filters should be sized in accordance with Table 1.

Outdoor Coil

Leaves and other large obstructions should be carefully removed from the outdoor coil surfaces without damaging the fin surface of the coil.

Lubrication

Lubrication of the bearings in the circulating air blower motor and the combustion blower motor is not recommended.

Blower Assembly

Even with good filters properly in place, blower wheels and motors will become dust laden after long months of operation. The entire blower assembly should be inspected annually. If the motor and wheel are heavily coated with dust, they can be brushed and cleaned with a vacuum cleaner.

Typical Flame Appearance

Figure 3

Burner Flame

While the unit is in operation, observe the burner flames. Compare these observations to Figure 3 to determine if proper flame adjustment is present. If your observations indicate improper flame adjustment, call your authorized service dealer for service. Do not attempt to adjust flame! Your service representative will perform this adjustment correctly.

Rollout Switch

This unit is equipped with a manual reset high temperature sensor or rollout switch. In the unlikely event of a sustained burner flame rollout, the rollout switch will shut off the flow of gas by closing the gas valve. The switch is located inside the gas burner area. Flame rollout can be caused by blockage of the power vent system, a blocked heat exchanger, or improper gas pressure or adjustment. If this event occurs, the unit will not operate properly. The gas supply to the unit should be shut off and no attempt should be made to place it in operation. The system should be inspected by a qualified service technician.

Page 6

Issue 0912

506299-01

Page 5 Page 7
Page 6
Image 6
Allied Air Enterprises 506299-01 Return Air, Minimum Required Surface Area For Disposable Filters, Outdoor Coil
Page 5 Page 7

506299-01 specifications

Allied Air Enterprises has established a strong reputation in the HVAC industry, and its model 506299-01 continues this tradition of excellence. This unit stands out for its advanced engineering and innovative technologies designed to provide optimal comfort in residential and commercial settings.

One of the main features of the Allied Air Enterprises 506299-01 is its highly efficient operation. With a superior SEER (Seasonal Energy Efficiency Ratio) rating, this model ensures lower energy consumption while maintaining maximum cooling output. This not only contributes to a reduced carbon footprint but also leads to significant savings on energy bills for consumers.

The design of the 506299-01 incorporates advanced compressor technology, allowing for quieter operation while delivering powerful performance. This is particularly valuable for users who prioritize maintaining a serene indoor environment, as the unit operates with minimal noise disturbance.

In addition, the model is equipped with a multi-speed blower, enhancing airflow control and distribution throughout the space. This feature ensures that every corner of the room receives consistent temperature regulation, improving overall comfort. Furthermore, the unit's compact design makes it easy to install, even in tighter spaces, without compromising on efficiency or performance.

Durability is another hallmark of the Allied Air Enterprises 506299-01. The unit is constructed from high-quality materials, ensuring longevity and reliability under various operating conditions. This durability is complemented by a robust warranty, giving customers peace of mind regarding their investment.

Another notable characteristic is its smart technology integration. The 506299-01 is compatible with modern HVAC control systems, enabling users to automate their heating and cooling preferences through programmable thermostats or smart home systems. This not only adds to user convenience but also optimizes energy efficiency further by allowing precise control over heating and cooling cycles.

In summary, the Allied Air Enterprises 506299-01 is a testament to advanced HVAC technology, combining energy efficiency, quiet operation, and durability with modern convenience. Its thoughtful design makes it a reliable choice for anyone looking to enhance their indoor climate control capabilities while being mindful of energy consumption and overall efficiency. As such, it represents a valuable addition to any home or commercial environment striving for ultimate comfort and sustainability.
Top Page Image Contents