C: INSTALLING THE OPERATOR

STEP 13: CONFIGURE MCB FOR SAFE FINISH OR ELECTRIC EDGE OPERATION

If you have not installed a Safe Finish Photosystem or Electric Edge at this time proceed to Step 15 on Page 13.

In order for your Safe Finish Photosystem or Electric Edge to work properly you must configure the motor control board to work with these devices.

Make sure the power is disconnected from the operator and remove the unit’s cover. Locate the motor control board inside of the operator. Locate the Obstruction Jumper on the Control Board using the diagram at right. The Obstruction Jumper is a simple wire jumper located close the center of the motor control board. The letters “OBS” are silk-screened on the board just above the jumper and the letters “SW2” are silk-screened on the board just to the left the jumper.

With a small wire cutter cut this jumper in half and separate the two halves so they do not touch.

Location of Obstruction Jumper on MCB

OPERATOR MOTOR CONTROL BOARD

The motor control board is now configured for Safe Finish Photosystem or an Electric Edge operation.

STEP 14: ALIGNMENT AND INITIAL TEST OF SAFE FINISH PHOTOSYSTEM

AT THIS POINT PLUG CONNECT THE POWER TO THE OPERATOR.

A.Connect the power to the Garage Door Opener. Keep a portable transmitter with you to control the garage door opener. The red light on the receiver unit should now be on. If not, recheck that the mounting screws are tight then, if necessary, align the photosystem by slightly bending the wall bracket until proper operation is obtained.

B.Place an object (packing insert box or a similar object at least eight inches high) one foot in front of the transmitter or receiver. The red LED should go OFF and remain OFF until the object is removed. NOTE: There may be a slight delay in returning to normal depending upon how long the photosystem was blocked. If the light fails to go off when the object is placed in the path of the beam check the wire connections and the installation height of the units (see Steps 11 and 12).

C.Move to the center of the door. Make sure the red LED light is on. Move a solid object slowly through the beam. The LED should go OFF and then ON.

D.Using the pushbutton or transmitter, activate the opener and check that it will operate through the full open and close cycles. If not, re-align the photosystem by slightly bending the wall bracket until proper operation is obtained.

E.Tighten all mounting screws and bolts, loop and secure any extra wire.

AT THIS POINT PLUG DISCONNECT (REMOVE) THE POWER TO THE OPERATOR.

12

Page 11 Page 13
Page 12
Image 12
Allstar Products Group LT 50 owner manual AT this Point Plug Connect the Power to the Operator
Page 11 Page 13

LT 50 specifications

Allstar Products Group LT 50 is a versatile and innovative product that has garnered attention for its efficiency and practicality. Designed with the modern consumer in mind, the LT 50 excels in various applications, making it a valuable addition to any home or workspace.

One of the standout features of the LT 50 is its impressive performance capabilities. Equipped with a powerful motor, this device is engineered to deliver quick and reliable results, whether it’s for light-duty tasks or more demanding jobs. The motor is designed to operate quietly, which enhances user experience, allowing for use in environments where noise might be a concern.

The LT 50 integrates advanced technologies that contribute to its ease of use and versatility. It boasts an ergonomic design, which ensures that the user can comfortably handle the device for extended periods. This thoughtful design extends to its controls, which are user-friendly and intuitive. The layout of buttons and switches allows for seamless operation, making it ideal for both seasoned users and novices alike.

Built with durability in mind, the LT 50 uses high-quality materials that withstand wear and tear over time. This longevity ensures that the product remains reliable throughout its lifespan, providing excellent value for consumers who seek dependable performance. Additional safety features are incorporated to prevent accidents and enhance user protection, making it a smart choice for families.

In terms of versatility, the LT 50 can be adapted for a range of tasks. Whether it’s household projects, maintenance work, or creative endeavors, this product has proven to be highly efficient. Its compact size makes it easy to store, and its lightweight construction facilitates portability, allowing users to take it wherever it's needed without hassle.

Furthermore, the LT 50 boasts excellent energy efficiency, making it an environmentally friendly option. By minimizing energy consumption while maximizing performance, it aligns perfectly with sustainable practices, catering to the growing number of eco-conscious consumers.

In conclusion, Allstar Products Group LT 50 is a well-rounded product that emphasizes performance, durability, and user-friendliness. Its innovative features and reliable technology make it an essential tool for everyday tasks, ensuring that consumers can tackle projects with ease and confidence. With the LT 50, users can expect nothing short of quality and efficiency in their endeavors.
Top Page Image Contents