TROUBLESHOOTING GUIDE

USE EXTREME CAUTION AT ALL TIMES WHEN ATTEMPTING TO DIAGNOSE WARNING AND RECTIFY PROBLEMS WITH YOUR GARAGE DOOR OPENER. BEFORE ATTEMPTING ANY SERVICE ON UNIT, DISCONNECT OPENER FROM POWER SUPPLY. YOUR GARAGE DOOR IS THE LARGEST MOVING OBJECT IN YOUR

HOUSE, AND THE SPRINGS, PULLEYS, CABLES AND MOUNTING HARDWARE UTILIZED TO BALANCE ITS OPERATION ARE UNDER EXTREME TENSION AT ALL TIMES AND CAN CAUSE SERIOUS PERSONAL INJURY, EVEN DEATH, IF DISTURBED. CALL AN EXPERIENCED SERVICE PERSON TO MOVE, LOOSEN OR ADJUST DOOR SPRINGS OR HARDWARE.

SYMPTOM:

PROBABLE CAUSE/SOLUTION:

Opener does not activate

(1)

(2)

(3) (4) (5) (6) (7) (15)

Operates with Push Button but not with radio control

(8)

(9)

(21) (12) (23)

Stops before reaching full Open or Closed position

(3)

(5)

(6) (10) (11) (13) (14) (23)

Reverses before reaching Full Close position

(6)

(11)

(14)

Reverses after door closes and contacts floor

(16)

(17)

Door opens and closes by itself

(3)

(18)

(23)

Light will not come on

(19)

(7)

 

Light will not turn off after Opener runs

(20)

(7)

 

Transmitter has short range

(8)

(21)

(12) (23)

PROBABLE CAUSE:

1.Mechanical door lock enabled

2.120 Volt power not present at terminal block

3.Broken or shorted Push Button, wiring or radio receiver

4.Grid lock on Motor Control Board

5.Motor Thermal Overload Protector opened

6.Door jammed due to broken or incorrectly adjusted spring

7.Defective Motor Control Board

8.Weak Battery in Transmitter

9.Radio Coding Switches mismatched

10.Improper placement of Limit Stops on Chain

11.Door obstructed

12.Defective Transmitter or Receiver

13.Up sensitivity force improperly adjusted

14.Down sensitivity force improperly adjusted

15.Bottom of door frozen to ground

16.Ice and snow built up under door

17.Floor risen or sunk from weather change

18.Someone in area with identical code

19.Defective or burned out lamp bulb

20.Radio Receiver not receiving signal

21.Transmitter location in car

SOLUTION:

1.Disable or remove all door locks.

2.Check wall switch, fuse box, circuit breaker, etc.

3.Remove Push Button wiring and Radio Receiver from the ter- minal strip on the back panel of the operator. Activate Opener by momentarily connecting Terminals 1 & 2 with a test wire. If Opener runs, reconnect items one at a time to find defective circuit. Replace.

4.Disconnect power to Opener, then reconnect.

5.Wait 30 minutes for Motor to cool, try again.

6.Ensure that door is in a closed position. Activate Manual Re- lease Mechanism. If Opener will run without door attached, contact your Allstar garage door professional to repair door

7.Contact your local Allstar garage door professional.

8.Replace Battery.

9.Reset Switches to identical codes (See instructions).

10.See instructions for proper placement of Limit Stops.

11.Remove all obstructions from door area.

12.Contact your Allstar garage door professional.

13.Adjust sensitivity. See instructions.

14.Adjust sensitivity. See instructions.

15.Activate Manual Release, clear away ice.

16.Clear away ice and snow to allow door to close.

17.See instructions to reset Down Limit Cam.

18.Reset all radio controls to new code.

19.Replace with rough service bulb (75W max.)

20.Ensure that antenna wire from Opener is pointing straight down toward the floor.

21.Ensure Transmitter is clipped to sun visor. If it is clipped to dashboard or in ashtray, etc., range will be diminished.

22

Page 22
Image 22
Allstar Products Group LT 50 owner manual Troubleshooting Guide, Symptom Probable CAUSE/SOLUTION

LT 50 specifications

Allstar Products Group LT 50 is a versatile and innovative product that has garnered attention for its efficiency and practicality. Designed with the modern consumer in mind, the LT 50 excels in various applications, making it a valuable addition to any home or workspace.

One of the standout features of the LT 50 is its impressive performance capabilities. Equipped with a powerful motor, this device is engineered to deliver quick and reliable results, whether it’s for light-duty tasks or more demanding jobs. The motor is designed to operate quietly, which enhances user experience, allowing for use in environments where noise might be a concern.

The LT 50 integrates advanced technologies that contribute to its ease of use and versatility. It boasts an ergonomic design, which ensures that the user can comfortably handle the device for extended periods. This thoughtful design extends to its controls, which are user-friendly and intuitive. The layout of buttons and switches allows for seamless operation, making it ideal for both seasoned users and novices alike.

Built with durability in mind, the LT 50 uses high-quality materials that withstand wear and tear over time. This longevity ensures that the product remains reliable throughout its lifespan, providing excellent value for consumers who seek dependable performance. Additional safety features are incorporated to prevent accidents and enhance user protection, making it a smart choice for families.

In terms of versatility, the LT 50 can be adapted for a range of tasks. Whether it’s household projects, maintenance work, or creative endeavors, this product has proven to be highly efficient. Its compact size makes it easy to store, and its lightweight construction facilitates portability, allowing users to take it wherever it's needed without hassle.

Furthermore, the LT 50 boasts excellent energy efficiency, making it an environmentally friendly option. By minimizing energy consumption while maximizing performance, it aligns perfectly with sustainable practices, catering to the growing number of eco-conscious consumers.

In conclusion, Allstar Products Group LT 50 is a well-rounded product that emphasizes performance, durability, and user-friendliness. Its innovative features and reliable technology make it an essential tool for everyday tasks, ensuring that consumers can tackle projects with ease and confidence. With the LT 50, users can expect nothing short of quality and efficiency in their endeavors.