Adjusting the Graphic Equalizer Curve

You can modify the equalizer settings to create a response curve more appealing to your personal taste. To adjust the graphic equalizer curve, set the EQ MODE to GRAPHIC EQ. For details, refer to “Setting EQ mode” (page 29).

1 After selecting GRAPHIC EQ from the SOUND ADJUST mode, press BAND to select the band to be adjusted.

B 1 B 2 B 3 B 4 B 5 B 6 B 7 B 1

Band-1 (63 Hz) / Band-2 (150 Hz) / Band-3 (400 Hz) / Band-4 (1 kHz) / Band-5 (2.5 kHz) / Band-6 (6.3 kHz) / Band-7 (17.5 kHz)

2 Turn the Rotary encoder to adjust the level.

Adjustable output level: -6 to +6 dB

3 To adjust another band, repeat steps 1 and 2, and then adjust all bands.

Adjusting the Time Correction

Before performing the following procedures, refer to “About Time Correction” (page 32).

1 After selecting T.CORRECTION from the SOUND ADJUST mode, press BAND to select a speaker to be adjusted.

2.2ch (3WAY) System

F-L (Initial setting)

 

F-R

 

R-L

 

 

R-R

 

(Mid-L)

 

(Mid-R)

(High-L )

(High-R)

SW-L SW-R F-L (Mid-L)

4.2ch (FRONT/REAR/SUBW.) System

F-L (Initial setting)

 

F-R

 

 

R-L

 

R-R

 

(Front-L)

 

(Front-R)

(Rear-L)

(Rear-R)

SW-L SW-R F-L (Front-L)

2 Turn the Rotary encoder to adjust the distance correction value. (0.0 to 336.6cm).

L = (distance to farthest speaker) – (distance to other speakers)

Refer to “Time Correction Value List” on page 32.

3 Repeat steps 1 and 2 to set another speaker.

By setting these values to make its sound reach the listening position at the same time as the sound of other speakers.

30-EN

Adjusting the Crossover Settings

Before performing the following procedures, refer to “About the Crossover” (page 33).

2.2ch (3WAY) System

1 After selecting CROSSOVER from the SOUND ADJUST mode, press BAND to select the band to be adjusted.

2.2ch (3WAY) System / NORMAL (L=R)

Setting items:

LOW / M-L / M-H / HIGH

2.2ch (3WAY) System / INDIVIDUAL (L/R)

Setting items:

L-L / L-R / ML-L / ML-R / MH-L / MH-R / H-L / H-R

2 Press or to select the desired cut-off frequency (Crossover Point).

Adjustable frequency bands:

2.2ch (3WAY) System

Setting items:

 

LOW / M-L

20 Hz~200 Hz

M-H

20 Hz~20 kHz

HIGH

(1 kHz~20 kHz)*1/(20 Hz~20 kHz)*2

*1 When MAKER’S is selected, refer to “Setting the Response Slope for the High Range Speaker (TW SETUP)” (page 28).

*2 When USER’S is selected, refer to “Setting the Response Slope for the High Range Speaker (TW SETUP)” (page 28).

3 Press SOURCE/ to adjust the slope.

Adjustable slope: FLAT*, 6 dB/oct., 12 dB/oct., 18 dB/oct.,

24dB/oct.

*FLAT can be set for the HIGH slope only when USER’S is selected in “Setting the Response Slope for the High Range Speaker (TW SETUP)” (page 28). Depending on the response characteristics of the speaker, care should be taken when setting the response slope to FLAT, as speaker damage may result. With this unit, a message is displayed when the response slope for the high range speaker is set to FLAT.

4 Turn the Rotary encoder to adjust the output level.

Adjustable output level: -12 to 0 dB.

5 Repeat steps 1 to 4 to make adjustment to the other bands.