English

 

Français

 

Español

INSTALLATION

INSTALLATION

INSTALACIÓN

Due to the high power output of the MRP-F240/MRP- T220, considerable heat is produced when the amplifier is in operation. For this reason, the amplifier should be mounted in a location which will allow for free circula- tion of air, such as inside the trunk. For alternate instal- lation locations, please contact your authorized Alpine dealer.

1.Using the amplifier as a template, mark the four screw locations.

2.Make sure there are no objects behind the surface that may become damaged during drilling.

3.Drill the screw holes.

4.Position the MRP-F240/MRP-T220 over the screw holes, and secure with four self-tapping screws.

NOTE:

To securely connect the ground lead, use an already in- stalled screw on the metal part of the vehicle (marked (★)). Be sure this is a good ground by checking conti- nuity to the battery (–) terminal. As much as possible connect all equipment to the same ground point. These procedures1 will help eliminate noise.

2Self-Tapping Screws (M4 x 14)

3Ground Lead

4Chassis Holes

En raison de la sortie de puissance élevée du MRP-F240/ MRP-T220, une forte chaleur est produite pendant le fonctionnement de l'amplificateur. Pour cette raison, l'amplificateur doit être monté dans un endroit permet- tant une bonne ventilation, tel que le coffre. Pour ce qui concerne les différentes positions d'installation, contac- ter un concessionnaire Alpine.

1.Apposer l'amplificateur contre la surface d'installa- tion pour marquer les repères des quatre vis.

2.Vérifier qu'il n'y a pas d'objets derrière la surface pouvant être abîmés lorsque les trous soient percés.

3.Percer les trous pour les vis.

4.PositionnerleMRP-F240/MRP-T220 pardessuslestrous et fixer avec les quatre vis auto-taraudées.

REMARQUE:

Pour connecter solidement le conducteur de mise à la terre, utiliser la vis déjà fixée sur la partie métallique du véhicule (signalée (★)). Assurez-vous que ce point est une bonne mise

àla terre en vérifiant la continuité à la borne de la batterie (–). Si possible, connecter tout l'équipement au même point de

1mise à la terre. Ceci vous aidera à éliminer le bruit.

2Vis auto-taraudées (M4 x 14)

3Conducteur de mise à la terre

4Châssis Trous

Debidoalasalidadealtapotenciadel MRP-F240/MRP-T220, se produce un calor considerable cuando el amplificador está en funcionamiento. Por esta razón, el amplificador deberá montarse en una ubicación que permita la libre circulación de aire, como por ejemplo dentro del maletero. Para ubica- ciones de instalación alternativas, por favor contacte a su dis- tribuidor de Alpine autorizado.

1.Utilizando el amplificador como plantilla, marque la ubicación de los cuatro tornillos.

2.Asegúrese de que no hay objeto alguno bajo la su- perficie que pueda verse dañado durante la perfora- ción de los agujeros.

3.Perfore los agujeros para los tornillos.

4.Sitúe el MRP-F240/MRP-T220 sobre dichos agujeros, y asegúrelo con cuatro tornillos autorroscantes.

NOTA:

Para conectar de forma segura el cable de tierra, utilice un tornillo ya instalado en la parte metálica del vehículo (marca- do (★)). Asegúrese de que es un punto de tierra bueno veri- ficando la continuidad con el terminal de la batería (–). Co- necte siempre que sea posible todo el equipo en el mismo punto1de tierra. Esto ayudará a eliminar el ruido.

2Tornillos autorroscantes (M4 x 14)

3Cable de tierra

4Chasis Agujeros

1

2

★

3

Fig. 1

4

5

Page 4 Page 6
Page 5
Image 5
Alpine MRP-T220, MRP-F240 owner manual Remarque, Nota
Page 4 Page 6

MRP-T220, MRP-F240 specifications

The Alpine MRP-F240 and MRP-T220 are two amplifiers that embody the essence of Alpine's commitment to high-quality audio performance. Each model is designed to deliver exceptional sound clarity and power, catering to the needs of audio enthusiasts and casual listeners alike.

The MRP-F240 is a four-channel amplifier that delivers a robust 60 watts RMS per channel at 4 ohms, allowing for a dynamic sound that can easily power multiple speakers in your vehicle. With a frequency response range of 20 Hz to 20 kHz, it captures the full spectrum of sound, from deep bass to crisp highs. It features an advanced MOSFET power supply, which enhances efficiency and minimizes distortion, ensuring that your music sounds its best at any volume. Its built-in high-pass and low-pass filters allow for precise tuning of the sound, making it adaptable to different audio setups.

On the other hand, the MRP-T220 is a compact two-channel amplifier that provides 75 watts RMS per channel at 4 ohms. Its small size does not compromise its power, making it an ideal choice for installations where space is limited. The MRP-T220 also employs a MOSFET power supply, ensuring powerful, clear sound reproduction. Its versatility allows it to be used in various configurations, whether powering coaxial speakers, component speakers, or even as a bridged amplifier to power a subwoofer.

Both amplifiers are built with high-quality components that enhance their durability and reliability. They are equipped with short protection and thermal protection circuits, safeguarding against damage in extreme conditions. A sleek, modern design ensures that they will look great in any vehicle while offering robust performance.

In terms of connectivity, both models offer RCA line inputs, making integration with head units easy and efficient. Their user-friendly setup process allows even those new to car audio installations to get great sound without a steep learning curve.

In conclusion, the Alpine MRP-F240 and MRP-T220 amplifiers represent the pinnacle of audio engineering within a compact form factor. They are designed to deliver clear, powerful sound while ensuring reliability through advanced technologies. Whether you are looking to enhance your car's audio system or seeking a powerful amplifier for different applications, these models are top contenders in the competitive car audio market.
Top Page Image Contents