Alto-Shaam 1000-BQ2/192 danger, E L E Ctric A L Connection, Ensure Power Source, d a n g e r

ins ta l l at i on

E L E CTRIC A L CONNECTION

	danger				d a n g e r
	ENSURE POWER SOURCE					To avoid electrical shock, this
	MATCHES VOLTAGE IDENTIFIED					appliance MUST be adequately
	ON APPLIANCE RATING TAG.					grounded in accordance with local
						electrical codes or, in the absence of
						local codes, with the current edition
	danger
						NFPA No. 70. In Canada, all electrical
						of the National Electrical Code ANSI/
						connections are to be made in
	ELECTRICAL CONNECTIONS MUST
						accordance with CSA C22.1, Canadian
	BE MADE BY A QUALIFIED SERVICE
						Electrical Code Part 1 or local codes.
	TECHNICIAN IN ACCORDANCE WITH
	APPLICABLE ELECTRICAL CODES.
1. An identification tag is permanently mounted		ELECTRICAL • 1000-BQ2/96
on the cabinet.			voltage	phase	cycle/hz amps			kW	cord & plug
				1				1.5	nema 5-15p
2. Plug cabinet into a properly grounded		120			60		12.5
									15A- 125V plug
receptacle ONLY, positioning the unit so the		208		1	60		5.9	1.2	nema 6-15p
power supply cord is easily accessible in case		240		1	60		6.8	1.6	15A - 250V plug
of an emergency.		230		1	50/60		6.5	1.5	cee 7/7
3. If necessary, a proper receptacle or outlet									plug rated 250V
									ch2-16p
configuration as required for this unit, must be
									plug rated 250V
installed by a licensed electrician in accordance
									BS 1363 (u.k. only)
with applicable, local electrical codes.
									plug rated 250V
nOTe: Where local codes and CE regulatory		ELECTRICAL • 1000-BQ2/128
			voltage	phase	cycle/hz		amps	kW	cord & plug included
requirements apply, appliances must be
		120		1	60		17.5	2.1	nema 5-30p
connected to an electrical circuit that is
									30A- 125V plug
protected by an external GFCI outlet.
		208		1	60		7.7	1.6	nema 6-15p
For CE approved units: To prevent an electrical		240		1	60		8.9	2.1	15A - 250V plug
		230		1	50/60		8.4	2.0	cee 7/7
shock hazard between the appliance and other
appliances or metal parts in close vicinity, an									plug rated 250V
									ch2-16p
equalization-bonding stud is provided. An
									plug rated 250V
equalization bonding lead must be connected to
									BS 1363 (u.k. only)
this stud and the other appliances / metal parts
									plug rated 250V
to provide sufficient protection against potential
difference. The terminal is marked		ELECTRICAL • 1000-BQ2/192
with the following symbol.			voltage	phase	cycle/hz		amps	kW	cord & plug included
		120		1	60		24.0	2.9	nema 5-20p
hard wired models:		power switch in low position					16.0	1.9	20A- 125V plug
									nema 5-30p
Hard wired models must be equipped with a		power switch in high position					25.0 max	3.0	30A - 125V plug
country certified external allpole disconnection		208		1	60		11.8	2.5	nema 6-15p
switch with sufficient contact separation.		240		1	60		13.6	3.3	15A - 250V plug
If a power cord is used for the connection of the		230		1	50/60		13.0	3.0	cee 7/7
product an oil resistant cord like H05RN or H07RN									plug rated 250V
or equivalent must be used.									ch2-16p
									plug rated 250V
									BS 1363 (u.k. only)
									plug rated 250V
			Wire diagrams are located inside the top of the unit.

1000-BQ2 (Rev. 1) series operation & care manual • 7