INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation. The parts supplied are in the washer drum.
Tools needed for connecting the water inlet hoses
■Pliers (that open to 19/16" [39.5 mm])
■Flashlight (optional)
Tools needed for connecting the drain hose
■Locking pliers (that open to 19/16" [39.5 mm])
Tools needed for installation
■Open end wrenches 14 mm and 13 mm
■Level
■Wood block
■Ruler or measuring tape
Parts supplied
Options
Pedestal
You have the option of purchasing pedestal separately for this washer. You may select a 10" (254 mm) or a 15.5" (394 mm) pedestal. The pedestal will add to the total height of the washer.
A
EF
A. Drain hose form B. Inlet hose (2)
C. Inlet hose washer (4) D. Drain hose
B
C
D
G
E.Transport bolt hole plug (4)
F.Beaded strap G. Hose clamp
Optional pedestal
Pedestal | Approximate | Color | Model |
Height | Height with |
| Number |
| Washer |
|
|
|
|
|
|
10" (254 mm) | 46" (1168 mm) | White | MHP1000SQ |
|
|
|
|
15.5" (394 mm) | 51.5" (1308 mm) | White | XHP1550VW |
Stack Kit
Are you planning to stack your washer and dryer? To do so you will need to purchase a Stack Kit.
Alternate Parts
Your installation may require additional parts. If you are interested in purchasing one of the items listed here, call the
If You Have | You Will Need to Buy |
|
|
Laundry tub or | Sump pump system (if not already |
standpipe taller | available) |
than 96" (2.4 m) |
|
|
|
Overhead sewer | Standard 20 gal. (76 L), 30" (762 mm) tall |
| drain tub or utility sink and sump pump |
| (available from local plumbing suppliers) |
|
|
Floor drain | Siphon break, Part Number 285320; |
| additional drain hose |
| Part Number 8318155; and connector |
| kit, Part Number 2858835 |
|
|
Drain hose too | 4 ft. (1.2 m) drain hose extension kit, |
short | Part Number 2858863 |
|
|
Water faucets | Longer water fill hose: |
beyond reach of fill | 10 ft. (3.0 m) Part Number 8212656RP |
hoses |
|
|
|
To order, call the dealer from whom you purchased your washer or refer to the “Assistance or Service” section. Ask for Part Number 8572546.
Location Requirements
Selecting the proper location for your washer improves performance and minimizes noise and possible washer “walk.”
Your washer can be installed under a custom counter, or in a basement, laundry room, closet, or recessed area. See “Drain System.”
Companion appliance location requirements should also be considered. Proper installation is your responsibility.
You will need
■A water heater set to deliver 120°F (49°C) water to the washer.
■A grounded electrical outlet located within 6 ft. (1.8 m) of where the power cord is attached to the back of the washer. See “Electrical Requirements.”
■Hot and cold water faucets located within 4 ft. (1.2 m) of the hot and cold water fill valves, and water pressure of
■A level floor with a maximum slope of 1" (25 mm) under entire washer. Installing the washer on soft floor surfaces, such as carpets or surfaces with foam backing, is not recommended.
■A sturdy and solid floor to support the washer with a total weight (water and load) of 400 lbs. (180 kg).
Do not operate your washer in temperatures below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures.
3
