V2000plus REAR PANEL

1

2

3

4

5

6

1

1 3

2 4

7

8

9

1. Cooling Fan -

Dual speed cooling fans. These fans are used to cool the internal parts of the amplifier. Never block the fan grills in any way or mount in an en- close rack, doing so may cause the amplifier to overheat and fail.

2. Channel 2 Input -

Connect the input source for channel two to either the balance XLR or the balanced/unbalanced 1/4” input jacks. The 1/4” TRS plug is configured as follows; Tip is positive, Ring is negative and Sleeve is ground. The XLR jack is configured as follows; Pin three positive, pin two negative, pin one ground. See page 9 for more details on input configuration.

3. Low Cut Filter Mode Switches -

These dip switches are used to active and adjust the built-in Low Cut Filter, see "Low Cut Filter" on page 14.

4. Channel 1 Input -

Connect the input source for channel one to either the balance XLR or the balanced/unbalanced 1/4” input jacks. The 1/4” TRS plug is configured as follows; Tip is positive, Ring is negative and Sleeve is ground. The XLR jack is configured as follows; Pin three positive, pin two negative, pin one ground. See page 9 for more details on input configuration.

5. Mono-Bridge/Stereo Selectable Switch -

This switch changes the amplifier operating mode from either stereo or mono bridge. Amplifiers are shipped in stereo mode.

6. Fuse Holder -

Diagram 3

10 11 12

This holder houses the external fuse. Always replace with the exact same type fuse unless otherwise instructed by an authorized American Audio® technician.

7. Channel 2 XLR THRU Jack -

This jack is used to send a parallel signal from the channel two input jacks to another device or amplifier.

8. Channel 1 XLR THRU Jack -

This jack is used to send a parallel signal from the channel one input jacks to another device or amplifier.

9. Channel 2 Output Jack/5 way Binding Post -

Connect to your speaker’s input jack. Red is positive signal and Black is negative signal.

10. Channel 1 Output Jack/5 way Binding Post -

Connect to your speaker’s input jack. Red is positive signal and Black is negative signal.

11. Ground Lift Switch -

This switch is used to disconnect the internal ground signal from the amplifier chassis ground. This may reduce the buzz that is caused from an electrical 60Hz cycle.

12. A/C Power Input -

Plug this cable in to a standard 110~120v wall outlet. Never plug your amplifier in to a wall outlet that does not match the required voltage of your amplifier, serious damage may occur to your unit.

American Audio® - www.americandj.com - Vplus Series Amplifiers Power Amplifier User Manual Page 7

Page 6 Page 8
Page 7
Image 7
American Audio Professional Power Amplifier manual V2000plus Rear Panel, Low Cut Filter Mode Switches
Page 6 Page 8

Professional Power Amplifier specifications

The American Audio Professional Power Amplifier is a key component in the realm of audio technology, designed to deliver high-quality sound reproduction across various applications, from live performances to permanent installations. Renowned for its robust build and exceptional performance, this amplifier brings together sophistication and reliability that meet the demands of professional sound engineers and audiophiles.

One of the standout features of the American Audio Professional Power Amplifier is its high power output, which can exceed 2000 watts in bridged mode. This allows it to drive large speaker systems effectively, producing dynamic range and clarity even at high volumes. The dual-channel configuration offers flexibility, allowing users to power multiple speakers or subwoofers simultaneously, an essential aspect in both DJ setups and band performances.

In terms of technology, the amplifier utilizes Class D amplification, known for its efficiency and lightweight design. Class D amplifiers generate less heat than traditional Class AB designs, allowing for better power handling and longer performance times without the risk of overheating. This efficiency also translates to reduced energy consumption, making it an environmentally friendly choice for both mobile and stationary setups.

The unit comes equipped with a range of protective features, including short-circuit protection, thermal overload protection, and peak limiters to ensure safe operation even under strenuous conditions. These features make it a reliable choice for professionals who cannot afford downtime during critical performances.

Connectivity options are plentiful, with the amplifier offering balanced XLR inputs as well as RCA connections, enabling integration with various audio sources. Furthermore, the output connections typically include binding posts and speakON connectors allowing for secure and reliable speaker connection.

User-friendly controls, such as gain controls for each channel and LED indicators for overload and protection status, make it easy to operate and monitor performance levels. Additionally, its rugged chassis design ensures durability, standing up to the rigors of frequent transport and use in diverse environments.

In conclusion, the American Audio Professional Power Amplifier stands out as a versatile, high-performance solution for professionals in the audio industry. Its powerful output, efficient Class D technology, protective features, and comprehensive connectivity options make it an indispensable tool for anyone seeking high-quality sound reinforcement. Whether for a live show or a fixed installation, this amplifier delivers the reliability and performance needed in professional settings.
Top Page Image Contents