American Standard 0955.021 dimensions Nominal Dimensions, Bowl sizes, Shroud/Knee Contact Guard

BARRIER FREE

MURRO™ UNIVERSAL DESIGN WALL-HUNG LAVATORY

VITREOUS CHINA

MURRO™ UNIVERSAL DESIGN WALL-HUNG LAVATORY

•Vitreous china

•Rear overflow

•Recessed self-draining deck

•For concealed arm or wall support

•Shown with optional vitreous china shroud/ knee contact guard 0059.020 available

❏0954.000 Faucet holes on 102mm (4") Ctrs (Illustrated)

❏0954.023 Faucet holes on 102mm (4") Ctrs

•Extra right-hand hole

❏0954.021 Faucet holes on 102mm (4") Ctrs

•Extra left-hand hole

❏0958.000 Faucet holes on 203mm (8") Ctrs

❏0955.000 Center hole only

❏0955.023 Center hole

•Extra right-hand hole

540mm

(21-1/4) 102mm

(4)

FINISHED	102mm	197mm
WALL	(4)	(7-3/4)
83mm	152mm
(3-1/4)
	(6)

❏0955.021 Center hole

• Extra left-hand hole

(4)25mm (1") DIA.

ACCESS HOLES

FOR CONC. ARMS

559mm

102mm(22)

(4)

	(2) 16mm (5/8") DIA.
	ACCESS HOLES
Nominal Dimensions:	FOR CONC. ARMS
			(16-3/4)	(5/8 X 1-1/8) ANCHOR
559mm (22") deep, 540mm (21-1/4") wide
			425mm	C/L OF 16mm X 29mm
	C/L OF 54mm(2-1/8 DIA.)			SLOTS
		HOLES FOR	216mm		FINISHED
Bowl sizes:	CONCEALED ARMS		(8-1/2)
					WALL
		44mm	127mm
394mm (15-1/2") wide, 343mm (13-1/2")			(5)	41mm
		(1-3/4)		(1-5/8)
front to back, 127mm (5") deep	406mm	165mm		146mm
	(16)	(6-1/2)		(5-3/4)
	REF.			*216mm
❏ 0059.020 Shroud/Knee Contact Guard	*(10-1/2)				203mm
				(8-1/2)	(8)
	267mm

(Vitreous China) (Must be specified separately)			C/L OF (2) 13mm(1/2) DIA.
			KNEE CONTACT GUARD
Compliance Certifications -		13mm(1/2) DIA.	ANCHOR HOLES	743mm
				(29-1/4)
		ANCHOR SCREW
							254mm
Meets or Exceeds the Following Specifications:		HOLES	C/L OF SUPPLIES	864mm		(10) REF.
	C/L OF 1-1/4		AS REQUIRED
		89mm		(34)
• ASME A112.19.2 for Vitreous China Fixtures	O.D. WASTE	(3-1/2)		(FRONT	SIDE PROFILE
				RIM)			(ADA)
To Be Specified:		1-1/4 O.D.	FLOOR
		TAILPIECE	FINISHED
❏ Color: ❏ White ❏ Bone ❏ Silver
❏ Optional Vitreous China Shroud/Knee	SEE REVERSE FOR ADDITIONAL ROUGHING-IN
Contact guard: 0059.020	DIMENSIONS
❏ Faucet*:
	NOTES:
❏ Faucet Finish:
	● LOOSE KEY ANGLE STOPS, LESS WALL ESCUTCHEONS. SUPPLIES
❏ Supplies:	REQUIRED.
❏ 1-1/4" Trap:	* DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE
	SUGGESTED.
❏ Nipple:	SHROUD/KNEE CONTACT GUARD 0059.020 NOT INCLUDED AND MUST BE
	ORDERED SEPARATELY.
* See faucet section for additional models available	■ SUITABLE FOR REINFORCEMENT ONLY, ACTUAL DIMENSIONS MUST
	BE TAKEN FROM FIXTURE.
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDE-	FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
	PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.
LINES AND ANSI A117.1 ACCESSIBLE AND USABLE	INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY.
BUILDINGS AND FACILITIES - CHECK LOCAL CODES.	IMPORTANT: Dimensions of fixtures are nominal and may vary within the
Top of front rim mounted 864mm (34") from finished floor.	range of tolerances established by ANSI Standard A112.19.2.
	These measurements are subject to change or cancellation. No responsibility
For Universal Design Options, top of rim may be mounted
	is assumed for use of superseded or voided pages.
at 813mm (32") from finished floor to meet ADA and ANSI
A117.1 requirements. Check local codes.	J61
© 2008 AS America Inc.				Revised 5/06