11TOILET CARE AND CLEANING
When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth. Avoid detergents, disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or abrasive pads on your toilet seat. Some bathroom chemicals and cosmetics may damage the seat's finish.
!WARNING: Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the tank. This damage can cause leakage and property damage. ChinaLux™ shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine (calcium hypochlorite).
TOILET SEAT CARE AND CLEANING
When cleaning your toilet seat wash it with mild, soapy water: rinse the seat thoroughly with clear water: and dry with a soft cloth.
Avoid detergents, disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders on your seat. Some bathroom chemicals and cosmetics may damage the seat's finish. After installation, check the tightness of the bolts from time to time to ensure a tight fit.
| PARTSLIST | NOTE: “XXX” represents color or trim finish options. Specify when ordering. | | |
REPAIR | PART NO. | DESCRIPTION | | PART NO. | DESCRIPTION |
120000.XXX | Chinaware cover | | 7381045-400.0070A | Flush Valve |
| | |
| | 7381044-0070A | Fill Valve | | 7381055-100.0070A | Flapper Assembly |
| | 738916-102.0070A | Refill Tube | | 7381046-XXX0A | Trip Lever |
| | 7301310-XXX0A | Tank Coupling Kit | | 034783-XXX0A | Bolt Cap Kit |
| | | | | | |
TROUBLESHOOTING GUIDE
PROBLEM | | POSSIBLE CAUSE | CORRECTIVE ACTION |
Does not flush | a. Water supply valve closed. | a. Open valve and allow water to fill tank. |
| b. Supply line blocked. | b. Shut off water supply, disconnect supply line, and inspect |
| | | all gaskets and washers. Reassemble. |
| c. Flush valve chain too loose or disconnected. | c. Readjust chain length as required. |
| d. Stuck float/float rod. | d. Adjust to allow free downward movement of float arm. |
| e. Water control flow rate too restricted. | e. Follow instructions to increase water control flow rate. |
| | |
Poor or | a. Tank water level too low. | a. Follow instructions to adjust water level. |
sluggish flush | b. Bowl water level too low. | b. Check that refill tube is connected to water control and |
| | | inserted into tank overflow without being kinked or damaged. |
| c. Supply valve partly closed. | c. Open supply valve fully. Be sure that proper supply tube size is used. |
| d. Flush valve closes early due to high | d. Follow instructions to reduce water control flow rate. |
| | supply pressure. | |
| e. Partially clogged trapway and/or | e. Remove obstruction. Consult a plumber if necessary. |
| | drain pipe and/or vent. | |
| f. | Supply pressure too low. | f. Normal supply pressure must be at least 20 psi. |
| | |
Toilet leaks | a. Poor supply line connection. | a. Review Step 9 of installation procedure. |
| b. Poor bowl to tank/floor connection. | b. Review Step 4 through 7 of installation procedure. |
| | |
Toilet does | a. Tank water level too high. | a. Follow instructions to adjust water level. |
not shut off | b. Float rod or float ball depressed by | b. Readjust float rod. |
| | tank cover. | |
| c. Flush valve chain too tight, holding | c. Readjust chain length as needed. |
| | flush valve open. | |
| d. Float rod interfering with flush valve closing. | d. Follow installation instructions to reduce water control flow rate, which |
| | | will lift lowest position of float rod without affecting water level. |
| e. Flush valve seat and/or flapper worn | e. Replace flapper/flush valve assembly, as needed. |
| | or deformed. | |
| f. | Sand or debris lodged in water control. | f. Shut off water supply. Consult a plumber, if necessary. |
| | | |
Noisy Flush | a. | Water control flow rate too restricted. | a. Follow instructions to increase water control flow rate. |
| | | |
CHINALUX ONE-YEAR LIMITED WARRANTY
If inspection of this ChinaLux™ plumbing product, within one year after its initial installation, confirms that it is defective in materials or workmanship, ChinaLux will repair or, at its option, exchange the product for a similar model.
This warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before installation.
This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or other damage; if it was not installed in accordance with ChinaLux’s instructions; or if it has been modified in a manner inconsistent with the product as shipped by ChinaLux.
ChinaLux’s option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation, nor shall ChinaLux be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product, all of which are expressly excluded from this warranty. (Some states or provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not apply to you.)
This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case this warranty does not affect such statutory rights.
For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that a service request (including a description of the product model and of the defect) be sent to the following address:
AS America Inc. | |
P.O. Box 6820, | For residents of the United States, warranty information may also be |
Piscataway, New Jersey 08855 |
Attention: Director of Consumer Affairs | obtained by calling the following toll free number: (800) 442-1902 |