American Standard 2907 installation instructions Recommended Tools And Materials, T U R E U S E

INSTALLATION INSTRUCTIONS

ANTIQUITY CADET® 3 - 1.6 GPF ONE-PIECE TOILET, MODEL 2907 COMPACT CADET® 3 - 1.6 GPF ONE-PIECE TOILET COMPACT CADET® 3 FloWise™ - 1.28 GPF ONE-PIECE TOILET

Model 2568 – Compact Elongated Right Height™ with Seat

Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.

!CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

NOTE: Pictures may not exactly define contour of china and components.

RECOMMENDED TOOLS AND MATERIALS

Putty Knife	Regular Screwdriver	Adjustable Wrench	Sealant	Tape Measure
Hacksaw	Wax Ring/Gasket	Flexible Supply Tube	Closet Bolts	Carpenters Level

1REMOVE OLD TOILET

a.Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.

b.Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!

c.Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.

d.Remove closet bolts from flange and clean away old wax, putty, etc. from base area. NOTE: Mounting surface must be clean and level before new toilet is installed!

2 ROUGHING-IN DIMENSIONS NOTE: Distance from wall to closet flange centerline must be as listed below:

T U R E U S E

ANTIQUITY CADET 3

FINISHED WALL

COMPACT CADET 3

FINISHED WALL

U

12.7mm (1/2")

225mm (8-7/8")

737mm

(29")

C/L OF SEAT POST HOLES 140mm (5-1/2) CENTERS

462mm

457mm

(18")

C/L

	724mm
16 ± 6mm	(28-1/2)
	381mm
(5/8 ± 1/4)	(15)
	159mm
	(6-1/4)
	C/L OF SEAT
	POST HOLES
	140mm (5-1/2)
	CENTERS

R F

(18-3/16)

419mm (16-1/2)

79mm (3-1/8)

422mm
(16-5/8)
419mm	724mm
	(28-1/2)
(16-1/2)	SUPPLY

F O

83mm (3-1/4")

235mm	360mm
(9-1/4)	(14-3/16)

305mm	C/L OF OUTLET
(12")

		714mm
		(28-1/8")
127mm
(5")
C/L OF SUPPLY	276mm	FINISHED
AS REQUIRED	(10-7/8)	FLOOR

267mm (10-1/2)

305mm (12)

		AS
		REQ'D
292mm	140mm		241mm
(11-1/2)	*	(5-1/2)	(9-1/2)	FINISHED
C/L OF OUTLET				FLOOR
			394mm
			(15-1/2)

S A V E

3

CLOSET FLANGE

A

CLOSET BOLTS

INSTALL CLOSET BOLTS

Install closet bolts in flange channel, turn 90°, and slide into place 6" (152 mm) apart and parallel to wall.

4

WAX RING

SEALANT

INSTALL WAX SEAL

Invert toilet on floor (cushion to prevent damage), and install wax ring evenly around waste flange (horn), with tapered end of ring facing toilet. Apply a thin bead of sealant around toilet base.

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c . © A S A m e r i c a , I n c . 2 0 0 9

7301270-100 Rev. D