American Standard 2568 installation instructions Recommended Tools And Materials, U R E U S E

Models: 2568

1 4
Download 4 pages 5.26 Kb
Page 1
Image 1
INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

COMPACT CADET® 3 - 1.6 GPF ONE-PIECE TOILET

COMPACT CADET® 3 FloWise™ - 1.28 GPF ONE-PIECE TOILET
Model 2568 – Compact Elongated Right Height™ with Seat

Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.

!CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

NOTE: Pictures may not exactly define contour of china and components.

RECOMMENDED TOOLS AND MATERIALS

Putty Knife

Regular Screwdriver

Adjustable Wrench

Sealant

Tape Measure

Hacksaw

Wax Ring/Gasket

Flexible Supply Tube

Closet Bolts

Carpenters Level

1REMOVE OLD TOILET

a.Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.

b.Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!

c.Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.

d.Remove closet bolts from flange and clean away old wax, putty, etc. from base area. NOTE: Mounting surface must be clean and level before new toilet is installed!

U R E U S E

2

ROUGHING-IN DIMENSIONS:

 

 

NOTE: Distance from wall to closet flange centerline must be as listed below:

 

 

FINISHED WALL

 

 

 

 

 

 

 

 

 

724mm

 

 

 

(28-1/2)

 

 

 

 

 

 

16 ± 6mm

381mm

 

 

(5/8 ± 1/4)

 

(15)

 

 

 

 

 

 

 

 

159mm

 

 

 

 

 

 

 

 

 

(6-1/4)

 

 

 

 

 

 

 

 

 

 

 

C/L OF SEAT POST HOLES 140mm (5-1/2) CENTERS

3

CLOSET FLANGE

A

R F U T

79mm (3-1/8)

COMPACT CADET® 3 - 1.6 GPF ONE-PIECE TOILET 267mm (10-1/2)

305mm

(12)

4

422mm

 

 

 

 

(16-5/8)

 

 

 

 

419mm

 

 

 

724mm

 

 

 

(28-1/2)

(16-1/2)

 

SUPPLY

 

 

 

 

AS

 

 

 

 

REQ'D

 

 

292mm

*

140mm

241mm

FINISHED

(11-1/2)

(5-1/2)

(9-1/2)

 

 

 

 

FLOOR

C/L OF OUTLET

 

 

394mm

 

 

 

 

(15-1/2)

 

 

 

 

 

5

CLOSET BOLTS COMPACT CADET® 3 FloWise™ - 1.28 GPF ONE-PIECE TOILETModel 2568 – Compact Elongated Right Height™ with Seat

INSTALL CLOSET BOLTS

Install closet bolts in flange channel, turn 90°, and slide into place 6" (152 mm) apart and parallel to wall.

S A V E F O

WAX RING

SEALANT

INSTALL WAX SEAL

Invert toilet on floor (cushion to prevent damage), and install wax ring evenly around waste flange (horn), with tapered end of ring facing toilet. Apply a thin bead of sealant around toilet base.

NUT

WASHER

THIS SIDEUP

BOLT

FLANGE

POSITION TOILET ON FLANGE

a.Unplug floor waste opening and install toilet on closet flange so bolts project through mounting holes.

b.Loosely install retainer washers and nuts. Side of washers marked "THIS

SIDE UP" must face up!

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .

7301270-100 Rev. A

© A S A m e r i c a , I n c . 2 0 0 8

Page 1
Image 1
American Standard 2568 installation instructions Recommended Tools And Materials, Remove Old Toilet, U R E U S E, R F U T