American Standard 2703.118W, 2705.118W, 2705.218W Ellisse Built-Inwhirlpool, American Standard Inc

ELLISSE BUILT-IN™ WHIRLPOOL

HIGH GLOSS ACRYLIC

SEE FITTING

SPECS FOR

DIMENSION

19mm

(3/4)

	1524mm
229mm	(60)	WATER RETENTION
(9)
		FLANGE (3) SIDES
	FINISHED
	WALL LINE

387mm (15-1/4)

PUMP

813mm
(32)				229x305mm
	C/L OF			(9x12) FLOOR
				CUTOUT
SUPPLIES
			51mm				ON/OFF SWITCH
				ALT. PUMP			PROVIDE ACCESS
			(2)
			C/L OF DRAIN	LOCATION		TO PUMP FOR SERVICING
			OUTLET				ON ALL INSTALLATIONS
			C/L OF		FINISHED WALL
		SHOWER ARM		C/L OF				1651-1981mm
		SAFE-T-HEATER		VALVES				(65-78)
		REMOVABLE BLANK						OPTIONAL
	102mm			C/L OF	WATER
305mm	(4)			SPOUT	RETENTION			38mm
(12) OPT.					FLANGE			(1-1/2)
TOP				■ LEVELING
OF		51mm			STRINGER			UNDERSIDE
DECK
	95mm	(2)	C/L OF		NOT FOR			OF DECK
					SUPPORT
	(3-3/4)	OVERFLOW
546mm				ROUGH			533mm
(21-1/2)				FLOOR
			INTEGRAL				(21)
			FEET
	ROUGH		1-1/2 N.P.T.
	FLOOR			38mm			83mm
			THREADS
				(1-1/2)			(3-1/4)
			1-1/2 O.D.
			TAILPIECE
			GENERAL SPECIFICATIONS FOR 2703/5 WHIRLPOOL
		INSTALLED SIZE		60 x 32 x 21-1/2 In. (1524 x 813 x 546mm)
		WEIGHT					141 Lbs. (63 Kg.)
		WEIGHT w/WATER					643 Lbs. (292 Kg.)
		GAL. TO OVERFLOW					60 Gal. (277 L)
		WHIRLPOOL MIN. OPERATING VOL.					50 Gal. (189 L)
		BATHING WELL AT SUMP		44-1/2 X 20 In. (1130 mm X 508 mm)
		BATHING WELL AT RIM		58 X 26-1/4 In. (1473 mm X 667 mm)
		WATER DEPTH TO OVERFLOW				14-1/2 In. (368 mm)
		FLOOR LOADING		48 Lbs./Sq.Ft. (231 Kgs./Sq.m)
		(PROJECTED AREA)
		PTS.						20.8
		CUBE (FT3)						35.3
			WHIRLPOOL ELECTRICAL SPECIFICATIONS
		SYSTEM I PUMP			1.6 HP, 9.7 AMPS, 120V.
		SYSTEM II PUMP			2.1 HP, 15.6 AMPS, 120V.

NOTES:

BATH MUST BE INSTALLED ABOVE THE FLOOR LINE AS BUILT-IN INSTALLATION. SUMP OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIAL BY OTHERS.

REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.

OPTIONAL APRON NO. 9160.2705 & GRAB BAR KIT NO.9827.200 AVAILABLE AND MUST BE ORDERED SEPARATELY.

FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

LEFT HAND OUTLET SHOWN, RIGHT HAND REVERSE DIMENSIONS 2703.118W/2705.118W.

PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.

IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING SYSTEM PIPING, DRAIN OVERFLOW, AND APRON INSTALLATION. MOUNTING HOLES DRILLED BY INSTALLER.

ON SYSTEM II: CONTROL MODULE TO BE MOUNTED BEHIND ACCESS PANEL, A MINIMUM OF 152mm (6) ABOVE ROUGH FLOOR.

IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1.These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.

© 2003 American Standard Inc.