American Standard 2902EC dimensions General Specifications for 2902E Whirlpool, Cube FT

SAVONA ELITE™ CORNER

WHIRLPOOLS BY AMERICAN STANDARD

HIGH GLOSS ACRYLIC

1492m	m	)
-3/4
(58

PROVIDE ACCESS	1067 mm
TO PUMP FOR
	(42)
SERVICING ON ALL

INSTALLATIONS

1588m	m
-1/2)
(62

IN-LINE HEATER

REMOVABLE BLANK

ON/OFF	1765 mm
SWITCH
	(69-1/2)

102mm (4)

1067 mm
(42)
● RECOMMENDED
FITTING LOCATION
64 X 330mm (2-1/2 X 13)
	203mm
	(8)
▲OUTLINE OF	C/L
CUTOUT
	1-1/2 O.D. DRAIN
1048mm	OUTLET
(41-1/4)

2096mm (82-1/2)

CUTOUT

IN FLOOR

FOR

DRAIN

914mm

(36)

PUMP

	51 mm	C/L OF
(2)
		OVERFLOW

■ LEVELING STRINGER NOT FOR SUPPORT

102mm

(4)

572 mm

(22-1/2)

521 mm

(20-1/2)

INTEGRAL	44 mm		ROUGH
	(1-3/4)
FEET		89 mm	FLOOR
		(3-1/2)

1-1/2 N.P.T.M.

1-1/2 O.D. TAILPIECE THREADS

GENERAL SPECIFICATIONS FOR 2902E WHIRLPOOL

INSTALLED SIZE		82-1/2 x 69-1/2 x 22-1/2 In.(2096 x 1765 x 572mm)
WEIGHT				144 Lbs. (65 Kg.)
WEIGHT w/WATER				803 Lbs. (361 Kg.)
GAL. TO OVERFLOW				79 Gal. (299 L)
WHIRLPOOL MIN. OPERATING VOL.				73 Gal. (277 L)
BATHING WELL AT SUMP				38 x 30 In. (965 x 762mm)
BATHING WELL AT RIM			58 x 55 In. (1473 x 1397mm)
WATER DEPTH TO OVERFLOW				15-3/4 In. (400mm)
FLOOR LOADING			33 Lbs./Sq.Ft. (165 Kgs./Sq.m)
(PROJECTED AREA)
PTS.			41.7
CUBE (FT3)					68.4
	WHIRLPOOL ELECTRICAL SPECIFICATIONS
PUMP				2.1 HP, 14.4 AMPS, 120V.

NOTES:

BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND OR PENINSULA TYPE INSTALLATION. SUMP OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIALS BY OTHERS.

OPTIONAL TILING BEAD KIT No. TILE-BEAD MUST BE ORDERED SEPARATELY.

■REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.

▲CUTOUT TEMPLATE PROVIDED IN SHIPPING BOX. MAY BE REQUESTED SEPARATELY. FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

●IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING SYSTEM PIPING AND DRAIN OVERFLOW. MOUNTING HOLES DRILLED BY INSTALLER.

PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.

IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1 / CSA Certified. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaflet.

© 2003 American Standard Inc.