5 | TEST INSTALLED FAUCET |
| ||
|
|
| Move HANDLE down into "off" position and remove AERATOR. |
|
|
|
|
| |
|
|
| Turn on water supplies and check connections for leaks. |
|
|
|
|
| |
|
|
| Operate HANDLE up and down, left and right to flush water | A E R AT O R |
|
|
| ||
|
|
| lines thoroughly. | |
|
|
| For faucet with spray, direct SPRAY HEAD into sink and |
|
|
|
|
| |
|
|
| activate SPRAY. Check hose connections for leaks. |
|
|
|
| Move HANDLE down to "off" position and replace AERATOR. |
|
|
|
|
| |
|
|
|
|
CHECK CONNECTIONS
FOR LEAKS
6 SERVICE
Reduced flow. If the flow gradually reduces over a number of months, the AERATOR may have collected debris. To clean, remove AERATOR and rinse with water and remove any debris. Turn on faucet to wash any debris out of the faucet. Thread AERATOR back into spout. Operate faucet.
Spout leakage. If fitting leaks above or below SPOUT HUB remove SPOUT as follows and check SPOUT
Remove HANDLE BUTTON (2) and loosen SET SCREW (1). Pull HANDLE (3) off valve stem.
1
2
3
4
5
6
Remove CAP (4) and and RETAINER (5). Loosen CARTRIDGE SCREWS (6) and | 12 | 7 | |
remove CARTRIDGE (7). | |||
|
|
Pull off SPACER (8) and
Remove SPOUT (12) by pulling up gently while moving SPOUT (12) side to side.
Check both SPOUT | A E R AT O R |
|
8
9
On models with SPRAYS, DIVERTER (10) can be cleaned by pulling | SPOUT |
DIVERTER (10) out of the MANIFOLD (13). Clean DIVERTER (10) and | HUB |
MANIFOLD (13). Push DIVERTER (10) back into MANIFOLD (10). | 11 |
Reverse procedure to reinstall SPOUT, CARTRIDGE and HANDLE.
Clogged CARTRIDGE outlets or inlets may cause reduced flow. | 13 |
To clean, first turn off water supply then: |
Remove PLUG BUTTON (2), loosen HANDLE SCREW (1) and remove HANDLE (3).
Remove ESCUTCHEON CAP (4). unscrew the three CARTRIDGE SCREWS (6).
Clean inlets of CARTRIDGE (7) and MANIFOLD (13).
10
Reassemble CARTRIDGE (7), alternately tightening SCREWS (6). Replace CAP (4) and HANDLE (3). Check flow.
HOT LIMIT SAFETY STOP ADJUSTMENT
By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP reduces risk of accidental scalding. To set the maximum hot water temperature of your faucets, all you need to do is adjust the setting on the HOT LIMIT SAFETY STOP.
Remove HANDLE BUTTON (1) and loosen SET SCREW (2). Pull |
|
HANDLE (3) off valve stem. Pull off CAP (4). Use a flat blade | "B" |
screwdriver or your fingers to pull up and rotate red |
|
HOT LIMIT SAFETY STOP (5). Follow Step "A" or "B" to adjust |
|
min./max.discharge temperature. "0" being the hottest to | "B" |
"7" the coldest temperature setting. Factory set at "0". |
| ADJUSTMENT WHEN |
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten | WATER IS TOO COLD |
| |
HANDLE SCREW (1) and install INDEX BUTTON (2). |
|
"A"
PRY RED RING FORWARD
AND ROTATE COUNTER-
CLOCKWISE ONE CLICK
|
|
|
|
| "A" | "A" |
|
|
|
|
|
| |
|
|
|
| 0 |
| ADJUSTMENT WHEN |
|
|
| 1 |
|
|
|
4 |
| 2 |
|
|
| WATER IS TOO HOT |
3 |
|
|
|
| ||
5 |
|
|
|
|
|
|
6 |
|
|
|
|
| 6 |
"B" |
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
| 5 |
|
|
|
|
| "RED RING"- HOT | |
|
|
|
|
| LIMIT SAFETY STOP |
M968202 REV . 1 . 2