The following instructions are for NOTE mounting fittings directly to the sink.

(Silhouette single bowl shown)

4 Apply a bead of sealant to the edge of the sink. Hold the sink against the under-side of

Countertop

Cutout

Edge

Sealant

1

Drill a clearance hole inside the cutout line.

Countertop

Template

Cutout

template

the countertop and rotate the clips to hold the sink in place. Snug the screws to hold the sink. Attach all the additional clips.

41mm

(1-5/8)

Support Clip

5

Countertop

2 Cut opening on cut line of the template.

Note - Formica counter- top installation only is illustrated. Contact your countertop distributor for the best method of cut- ting other materials such as marble, hard syn- thetics, etc.

Countertop

Template

Cutout

Mount the faucet and drain assembly following the manufacturer's instructions.

Sink

Surface

3 Attach at least four of the support clips to the underside

of the countertop as shown below. The location of the clips should be as shown in the sink diagram.

The wood screws are for use in wood, plywood, or particle board (drill appropriate pilot hole).The inserts supplied are for use in marble or hard synthetic material.

Support

Cutout

Clips

 

6

Connect supply lines to faucet finger tight, and carefully bend to engage with the supply stops. Tighten connections to faucet for secure seal.

7 Connect drain assembly

AMERICAST® LIMITED LIFETIME WARRANTY

If an American-Standard Americast® brand product is found to be defective in materials or workmanship, after inspection by an authorized American-Standard representative, American-Standard will repair or, at its option, exchange the product for a similar model. This warranty extends for the lifetime of the product, so long as it remains in use in its original place of installation, except that the warranty applies to a bathing vessel’s slip-resisting surface only for the first year after the product’s initial installation.

This warranty applies only to the original purchaser and installation of these products.

This warranty does not apply to whirlpool components or to faucets, drains, mounting rims, grab bars or other accessories. If manufactured or supplied by American- Standard, such whirlpool components and accessories are covered under separate limited warranties.

This warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should check with a local building or plumbing contractor to assure local code compliance before installation.

This warranty shall be void if the Americast® brand product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or other damage; if it was not installed in accordance with American-Standard’s instructions; or if it was modified in a manner inconsistent with the product as shipped by American-Standard.

American-Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation, nor shall American-

Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product, all of which are expressly excluded from this warranty. (Some states or provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not apply to you.)

This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case this warranty does not affect such statutory rights.

For service under these warranties, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that a service request (including a description of the product model and of the defect) be sent to the following address:

hand tight to check align-

 

 

ment. It may be necessary

 

 

to cut off part of the tailpiece

A

B

(area "A") or part of the

 

horizontal leg of the trap

 

 

(area "B").

 

 

Secure joint for watertight

 

 

assembly.

 

 

Trap

Trap

 

 

 

Single Bowl

Double Bowl

CARE AND CLEANING...

For all porcelain enamel surfaces, regular, gentle care is best. The recommended way to preserve the finish, avoid scratches, and clean porcelain enamel fixtures is to rinse them with detergent and water. Generally, any of the light duty liquid dishwashing detergents, such as Palmolive or Dawn, work well. In areas where the water is hard, a heavy duty liquid

In the United States:

American Standard Inc.,

P.O. Box 6820

Piscataway, New Jersey 08855

Attention: Director of Consumer Affairs

For residents of the United States, warranty information may also be obtained by calling the following

toll free number: (800) 442-1902

In Canada:

American-Standard,

2480 Stanfield Road

Mississauga, Ontario

Canada L4Y 1S2

Toll Free: (800) 387-0369

laundry detergent such as liquid Tide will work better.

Product names listed herein are trademarks of American Standard Inc.unless otherwise noted. Palmolive® is a registered trademark of Colgate-Palmolive Co.

Tide® and Dawn® are registered trademarks of Procter and Gamble.

7 9 0 0 8 8 - 1 0 0 R E V . H

5

© A M E R I C A N S T A N D A R D I N C . 2 0 0 3

 

 

Page 7
Image 7
American Standard 7182.000, 7182.803, 7182.001 installation instructions Care and Cleaning, United States

7182.001, 7182.000, 7182.803 specifications

The American Standard 7182 series encompasses three refined bathroom faucets: the 7182.001, 7182.000, and 7182.803 models. These faucets are designed to deliver a harmonious blend of both style and functionality, making them ideal for modern bathrooms while retaining a classic touch.

One of the prominent features of the American Standard 7182 series is its WaterSense certification. This certification signifies that these faucets are designed to save water without sacrificing performance. By utilizing a flow rate of 1.2 gallons per minute, these faucets not only conserve water but also contribute to lower utility bills. This emphasis on sustainability makes the American Standard 7182 series a smart choice for eco-conscious homeowners.

The design of the 7182 models is another standout aspect. With sleek lines and a polished finish, these faucets easily complement a variety of bathroom styles—from contemporary to traditional. The 7182.001 features a bold, angular spout that adds a modern edge, while the 7182.000 presents a more rounded, soft silhouette perfect for classic aesthetics. The 7182.803 introduces a unique cross handle design that provides a vintage charm, appealing to those who appreciate retro decor.

In terms of technology, the American Standard 7182 series incorporates solid brass construction, which ensures durability and longevity. This robust material is resistant to corrosion, making these faucets a reliable choice for daily use. To enhance user experience, the faucets come with a ceramic disc valve that offers a drip-free performance and smooth operation. This technology not only prevents leaks but also ensures consistent water temperature control.

Installation of the 7182 faucets is straightforward, as they are designed to fit a standard three-hole configuration, making them compatible with most sinks. Additionally, these models come with all the necessary mounting hardware and clear instructions, allowing homeowners to install them with ease.

In summary, the American Standard 7182.001, 7182.000, and 7182.803 faucets stand out due to their stylish designs, water-saving features, durable materials, and advanced technology. Whether you prefer a modern or traditional look, this series offers versatile options that enhance any bathroom space while promoting environmental responsibility. With these faucets, homeowners can enjoy both aesthetic appeal and practical benefits for years to come.