American Standard 7182.001, 7182.803, 7182.000 After the Cutout is Drawn, Care and Cleaning

Silicone

Sealant

1	AFTER THE CUTOUT IS DRAWN...
	Drill a clearance hole
	inside the cutout line	Perimeter
	as marked on the
		of sink
	countertop.
		Cutout

5 Apply a masking tape outline 1/8" outside traced outline as a guide for application of silicone

sealant.

		Cutout
Masking	1/8"	Sink
tape		outline
outline

6 Apply a generous portion of silicone sealant inside line

2

Cut opening on cut line inside the peri- meter of sink.

Perimeter

of sink

Cutout

traced on countertop. Carefully lower sink into place and press down firmly. Use guidelines for proper positioning. Using water to dampen your finger, remove excess sealant for a smooth even line. Apply additional sealant if necessary to provide a uniform bead from the rim of sink to the masking tape line as shown. Carefully remove tape. Dampen finger and run it slightly over the sealant to remove any high spots.

3

Mount the faucet and drain assembly on the sink following the manufacturer's instructions.

4	Before applying the
	sealant, place the sink
	temporarily into the
	cutout. Check for
	alignment and clear-
	ance, then trace
	around the outside
	edge of the sink as
	a guide for installation location and application of
	sealant. Remove sink.
	AMERICAST® LIMITED LIFETIME WARRANTY

If an American-Standard Americast® brand product is found to be defective in materials or workmanship, after inspection by an authorized American-Standard representative, American- Standard will repair or, at its option, exchange the product for a similar model. This warranty extends for the lifetime of the product, so long as it remains in use in its original place of installation, except that the warranty applies to a bathing vessel’s slip-resisting surface only for the first year after the product’s initial installation.

This warranty applies only to the original purchaser and installation of these products.

This warranty does not apply to whirlpool components or to faucets, drains, mounting rims, grab bars or other accessories. If manufactured or supplied by American-Standard, such whirlpool components and accessories are covered under separate limited warranties.

This warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should check with a local building or plumbing contractor to assure local code compliance before installation.

This warranty shall be void if the Americast® brand product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or other damage; if it was not installed in accordance with American-Standard’s instructions; or if it was modified in a manner inconsistent with the product as shipped by American-Standard.

American-Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation, nor shall American-Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product, all of which are expressly excluded from this warranty. (Some states or provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not apply to you.)

This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case this warranty does not affect such statutory rights.

For service under these warranties, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that a service request (including a description of the product model and of the defect) be sent to the following address:

	In the United States:		In Canada:
	American Standard Inc.,
		American-Standard,
	P.O. Box 6820	2480 Stanfield Road
Piscataway, New Jersey 08855		Mississauga, Ontario
Attention: Director of Consumer Affairs		Canada L4Y 1S2
For residents of the United States,		Toll Free: (800) 387-0369
warranty information may also be
obtained by calling the following
toll free number: (800) 442-1902

Use mineral spirits to remove excess silicone from countertop and sink.

Sink

Masking

Tape

NOTE: Silicone must be removed within 10 minutes of application or a permanent residue may remain on the surfaces.

7 Connect supply lines to faucet finger tight, and carefully bend to engage with the supply stops. Tighten connections to faucet for secure seal.

8	Connect drain assembly
	hand tight to check
	alignment. It may be
	necessary to cut off part		B
	of the tailpiece (area "A")	A
	or part of the horizontal
	leg of the trap (area "B").
	Secure joint for water-
	tight assembly.
			Trap
		Single Bowl

CARE AND CLEANING...

For all porcelain enamel surfaces, regular, gentle care is best. The recommended way to preserve the finish, avoid scratches, and clean porcelain enamel fixtures is to rinse them with detergent and water. Generally, any of the light duty liquid dishwashing detergents, such as Palmolive or Dawn, work well. In areas where the water is hard, a heavy duty liquid laundry detergent such as liquid Tide will work better.

Product names listed herein are trademarks of American Standard Inc.unless otherwise noted. Palmolive® is a registered trademark of Colgate-Palmolive Co.

Tide® and Dawn® are registered trademarks of Procter and Gamble.

7 9 1 2 6 7 - 4 0 0 R e v . C 2 © American Standard Inc. 2003