American Standard 7222.722 Install Trim Shower and TUB Spout, Finishing Installation, Service

2	INSTALL TRIM (SHOWER AND TUB SPOUT)
	NOTE; PROTECT FINISH ON SHOWER AND TUB TRIM WHEN INSTALLING.
	Remove PLASTER GUARDS (1) from valve body by unthreading and pulling off.
	Remove rough-in nipple from shower elbow.	4
	Apply sealing tape to threads on both ends of SHOWER ARM (2) and install
	SHOWER ARM (2) with SHOWER ESCUTCHEON (3) into shower elbow.

3	SHOWER
2	ELBOW
	5
	ROUGH-IN
	NIPPLE
	AXI
	MUM

Thread SHOWER HEAD (4) onto end of SHOWER ARM (2). Push SHOWER

ESCUTCHEON (3) against finished wall. Tighten SET SCREW (5).

Remove pipe cap from tub filler pipe. Prepare TUB FILLER PIPE, ELBOW and	1
1/2" COPPER PIPE. Final length of COPPER PIPE to be 1" from
finished wall.
Push SPOUT ESCUTCHEON (6) onto filler pipe flush against finished wall.
Push TUB SPOUT (7) onto filler pipe until tight against SPOUT ESCUTCHEON (6).
Tighten clamp screw in SPOUT (7) to secure TUB SPOUT (7).	7

M

MIN US

AXI
MUM
MIN US	M
	M

6 ROUGH-IN NIPPLE

1"

PIPE CAP

CLAMP SCREW

3 FINISHING INSTALLATION

Remove caps from roughing-in nipples.

Remove PLASTER GUARD by turning counter-clockwise and pulling.

If VALVE BODY is roughed in SHALLOW (more than 2-1/2") screw SLEEVE in ESCUTCHEON facing front of ESCUTCHEON.

If VALVE BODY is roughed in DEEP (less than2-1/2") screw SLEEVE in ESCUTCHEON facing back of ESCUTCHEON.

Assemble RUBBER RING to ESCUTCHEON.

Screw ESCUTCHEON and SLEEVE onto VALVE COVER against wall. Install SHOWER ARM, SHOWER ARM FLANGE and TUB SPOUT.

SHALLOW ROUGH-IN

MORE THAN 2-1/2"

SLEEVE

VALVE

COVER

RUBBER

RING VALVE

BODY

DEEP ROUGH-IN

LESS THAN 2-1/2"

SLEEVE

ESCUTCHEON

4 INSTALL HANDLES

7

FOR CROSS HANDLES

Turn VALVE into OFF position.

Push ADAPTER (1) into HANDLE BASE (2) in a way that the male square on the ADAPTER (1) fits in the female square of the HANDLE BASE (2).

Push HANDLE BASE (2) and	8
ADAPTER (1) onto VALVE STEM (3).

Push CROSS HANDLE (4, 5) onto

HANDLE BASE (2).

Install HANDLE SCREW (6) and tighten.

Push INDEX CAP (7, 8) in top of

CROSS HANDLE.

6 4 1 3

2

9

67 6 METAL

LEVER

5

FOR LEVER HANDLES

Turn VALVE into OFF position.

Push ADAPTER (1) into HANDLE BASE (9) in a way that the male square on the ADAPTER (1) fits in

he female square of the HANDLE BASE (9).

Push HANDLE (9) and ADAPTER (1) onto VALVE STEM (3).

Check alignment, if not satisfactory aligned;

Push out ADAPTER (1) carefully.

Turn ADAPTER (1) either 45˚ or 90˚ so that male square on ADAPTER (1) catches different female square in HANDLE BASE (9).

Assemble and tighten HANDLE SCREW (6). Push INDEX CAP (7) in top of HANDLE (9).

5 TEST INSTALLED FAUCET

Turn HANDLES into "off" position.

Turn on water supplies and check all connections for leaks.

Operate both HANDLES to flush water lines thoroughly.

Check SHOWER HEAD and SPOUT connections for leaks. Operate DIVERTER for proper operation. Turn handles into OFF position.

6	SERVICE	SPRING
		CLIP

To change direction of handle rotation, proceed as follows:

Turn valve to OFF position.
Pull out INDEX CAP and remove
HANDLE SCREW.
Pull out LEVER BALL from HANDLE BASE.	90˚
Unscrew HANDLE BASE and remove ADAPTER
Remove SPRING CLIP.
Lift STOP WASHER, turn 90 and replace.
Replace SPRING CLIP.	STOP
Reinstall HANDLE. (See step three).	WASHER

If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90 .

CARE:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE.

US60406REV. 1. 2