RONDO™ WHIRLPOOL
HIGH GLOSS ACRYLIC
●RECOMMENDED FITTING | 165mm | ||
LOCATION 64 X 279mm | |||
| |||
|
| ||
267mm |
|
| |
|
| ||
1067mm | PUMP | ||
|
| ||
(42) |
| ON/OFF | |
|
| SWITCH | |
1816mm
908mm
76mm
(3)C/L OF DRAIN
229 X 305mm (9 X 12) CUTOUT
PROVIDE ACCESS
TO PUMP FOR SERVICE ON ALL INSTALLATIONS
C/L OF
OVERFLOW
95mm
83mm
38mm 
▲OUTLINE OF
CUTOUT |
|
|
| ■LEVELING STRINGER | ||
|
|
| NOT FOR SUPPORT | |||
REMOVABLE BLANK |
|
|
|
|
| 51mm |
|
|
|
|
|
| |
|
|
| (2) | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
495mm
546mm
ROUGH
38 mm
FLOOR
TAILPIECEINTEGRAL
FEET
GENERAL SPECIFICATIONS FOR 7242 WHIRLPOOL
INSTALLED SIZE |
|
|
| ||||||||||||||||||||
|
|
| |||||||||||||||||||||
WEIGHT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 94 Lbs.(43 Kg.) | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
WEIGHT w/WATER |
|
|
|
|
|
|
|
|
|
|
| 818 Lbs.(371 Kg.) | |||||||||||
|
|
|
|
|
|
|
|
|
| ||||||||||||||
GAL. TO OVERFLOW |
|
|
|
|
|
|
|
|
|
|
|
|
| 87 Gal. (330 L) | |||||||||
WHIRLPOOL MIN. OPERATING VOL. |
|
|
|
|
|
|
|
| 67 Gal. (254 L) | ||||||||||||||
|
|
|
|
|
|
|
| ||||||||||||||||
BATHING WELL AT SUMP |
|
|
|
|
| 45 x 25 In. (1143 x 635mm) | |||||||||||||||||
BATHING WELL AT RIM |
|
|
|
|
|
| 60 x 30 In. (1524 x 762mm) | ||||||||||||||||
WATER DEPTH TO OVERFLOW |
|
|
|
|
|
| |||||||||||||||||
|
|
|
|
|
| ||||||||||||||||||
FLOOR LOADING |
|
|
|
|
| 39 Lbs./Sq.Ft. (191 Kgs./Sq.m) | |||||||||||||||||
|
|
|
|
| |||||||||||||||||||
(PROJECTED AREA) |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
PTS. |
|
|
|
|
|
|
|
|
|
|
|
| 30.3 | ||||||||||
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||
CUBE (FT3) |
|
|
|
|
|
|
|
| 58.7 | ||||||||||||||
|
|
|
|
|
|
|
| ||||||||||||||||
|
|
| WHIRLPOOL ELECTRICAL SPECIFICATIONS | ||||||||||||||||||||
SYSTEM II PUMP |
|
|
|
|
|
|
| 2.1 HP, 15.6 AMPS,120. | |||||||||||||||
|
|
|
|
|
|
| |||||||||||||||||
NOTES: BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND OR PENINSULA TYPE INSTALLATION. SUPPORT OF BATH BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. SUPPORT AND ENCLOSING MATERIAL BY OTHERS.
■REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
CUTOUT TEMPLATE PROVIDED IN SHIPPING BOX, MAY BE REQUESTED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.
●FITTINGS AND TWIST GRAB BAR NO . 750565 - 000 NOT INCLUDED, MUST BE ORDERED SEPARATELY.
●IF INSTALLING A
ON SYSTEM II: CONTROL MODULE TO BE MOUNTED BEHIND ACCESS PANEL, A MINIMUM OF 152mm (6) ABOVE ROUGH FLOOR.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1
These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaflet.
