1 CAUTION
Turn off hot and cold water supplies before beginning.
VALVE INSTALLATION
Remove ESCUTCHEONS with RUBBER RINGS and insert VALVE HOUSING through holes from underside of SINK. Thread of all three VALVE SHANKS should extend at least 5/16 inch above SINK top. If necessary, adjust LOCKNUTS.
Place RUBBER RINGS into ESCUTCHEONS' recess and thread ESCUTCHEONS onto VALVE HOUSING until snug against internal stop.
Center VALVE HOUSING on SINK and tighten LOCKNUTS (3) using
2 HAND SPRAY INSTALLATION
FOR MODEL 7231 AND 7271 ONLY:
Place SPRAY HOLDER into | SPRAY | |
HEAD | ||
separate hole of SINK. | ||
|
Assemble PLASTIC LOCKNUT onto SHANK of SPRAY HOLDER and tighten.
RUBBER
WASHER
WRENCH supplied with faucet.
Connect the HOT water supply to the left valve and the COLD water
Feed SPRAY HOSE through SPRAY HOLDER and attach COUPLING NUT of HOSE to
SPRAY
HOLDER
SPACER
supply to the right valve using sealant, appropriate connectors, and COUPLING NUTS.
|
|
|
|
|
|
|
|
|
|
|
|
|
| ESCUTCHEON |
HANDLE |
|
|
|
|
|
| RUBBER | |||||||
|
|
|
|
|
| RING | ||||||||
SCREW |
|
|
|
|
|
|
|
|
| |||||
5/16'' MIN. |
|
|
|
|
|
|
|
|
| SINK | ||||
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
RUBBER
WASHER
BRASS
WASHER
NIPPLE of VALVE CENTER. Tighten COUPLING NUT firmly.
Make certain that SPACER WASHER and RUBBER WASHER are attached to SPRAY HOSE and thread SPRAY HEAD to NUT.
WASHER
VALVE | NUT |
CENTER | SINK |
|
PLASTIC
LOCKNUT
NIPPLE
COUPLING
NUT
LOCKNUT
VALVE
BODY
SPRAY
HOSE
3 SPOUT INSTALLATION
Check that both
FOR MODELS WITH HAND SPRAY: Check that the DIVERTER PLUG is free and can move up and down.
Apply the grease (provided) liberally to the
Push the SPOUT SUBASSEMBLY on to the VALVE CENTER and tighten the SPOUT NUT until snug on valve body.
SPOUT
SUBASSEMBLY
SPOUT
NUT
DIVERTER
PLUG
4 TEST INSTALLED FAUCET
Remove AERATOR.
With handle in OFF position, turn on water supplies and check all connections for leaks.
5 SERVICE
To change direction of handle rotation, proceed as follows:
Operate both handles to flush water lines thoroughly. Check spout mounting and hose connections for leaks.
Turn handles into OFF position and replace AERATOR.
If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90° .
| Turn valve to OFF position. |
|
|
|
| Remove INSERT and HANDLE SCREW. | SPRING |
|
|
| Slip HANDLE with ADAPTER off. | CLIP |
| |
| Remove SPRING CLIP. | STOP |
| Lift STOP WASHER, turn 90° and replace. | |
| WASHER | |
| Replace SPRING CLIP. | |
|
| |
| Replace ADAPTER, HANDLE, SCREW, and INSERT. |
|
|
| |
|
|
AERATOR may accumulate dirt causing distorted and reduced water flow. Remove AERATOR and rinse clean.
HOTLINE FOR HELP
For
Plastic SCREEN in CARTRIDGE may accumulate dirt causing reduced water flow. To clean, first turn off hot and cold water supplies, then:
Remove INSERT and HANDLE SCREW.
Slip HANDLE with ADAPTER off.
Unscrew CARTRIDGE with wrench.
Thoroughly rinse plastic SCREEN at base of CARTRIDGE.
Replace CARTRIDGE until flange is tight against valve body.
Turn valves OFF.
Replace ADAPTER, HANDLE, SCREW, and INSERT.
CARTRIDGE
SCREEN
1 (800) 223-0068
Weekdays 8:00 a.m. to 4:00 p.m. Eastern Time
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c . C A m e r i c a n S t a n d a r d I n c . 1 9 9 9
M 3 4 4 5 0 B
