9b | 10 | TOP |
| ARM NIPPLE |
|
|
|
| REFILL |
|
|
|
| TUBE |
|
|
|
| TANK |
|
|
|
| LEVER |
|
| CRITICAL LEVEL |
|
|
|
| MARK ("C.L.") |
|
|
|
| MUST BE |
|
|
|
| 1" ABOVE |
|
|
|
| OVERFLOW PIPE | FLOAT | Fig. 10A |
|
|
| ||
|
|
| CUP | |
|
| FILL |
|
|
|
| VALVE |
|
|
|
|
|
| WATER LEVEL |
|
| VALVE |
| ADJUSTMENT |
|
|
| ROD | |
|
| BODY |
|
|
|
|
|
| ADJUSTABLE |
|
| SHANK |
| HEIGHT |
|
| WASHER |
|
|
LOCK NUT | THREADED |
| SHANK |
|
|
| CONE WASHER |
|
|
|
|
|
| PARTS FOR WATER |
|
|
|
| COUPLING NUT | CONNECTION |
|
|
|
| (SEE STEP 9) |
| |
|
|
| (HAND TIGHT ONLY) |
| |
|
|
|
| Diagram 1 | |
|
|
|
|
| |
|
| ADJUSTMENTS |
|
| |
| With correct washers in | a. Adjust water level. Water level should be adjusted to level indicated in | |||
| tank by adjusting float cup. See Step 11 for water level adjustment method. | ||||
| place (see Step 9a), | IMPORTANT: |
|
| |
| tighten COUPLING NUT |
|
| ||
| b. If bowl fails to siphon, an adjustment may be required with the lift chain. | ||||
| 1/4 turn beyond hand tight. | ||||
|
| Simply remove the bead chain from the retainment clip (see Fig. 10A) | |||
| DO NOT OVERTIGHTEN. | and take up slack on the chain, and reinsert on lift rod. Make sure the chain | |||
| is not too taught. |
|
| ||
|
|
|
| ||
11 | Turn on water supply. | 12 | CARE AND CLEANING |
| |
| Submerge the FLOAT |
| When cleaning your toilet, wash it with mild, soapy water, rinse | ||
| CUP under the water for |
| |||
|
| thoroughly with clear water and dry with a soft cloth. | |||
| 30 seconds. Adjust the |
| |||
|
| WARNING: Do not use | |||
| water to desired level by | ! | |||
| turning WATER LEVEL |
| can seriously damage fittings in the tank. This damage can | ||
| ADJUSTMENT ROD |
| cause leakage and property damage. |
| |
| and moving FLOAT |
| American Standard shall not be responsible or liable for | ||
| CUP up or down. |
| |||
|
| any damage caused by the use of | |||
|
|
| |||
13 | TROUBLE SHOOTING FLUSH VALVE | 13a REFILL TUBE REPLACEMENT: |
| ||
| SEAL REPLACEMENT: |
|
|
|
|
1.Turn off water supply and flush toilet to empty tank.
2.Disconnect chain from trip lever by removing hair pin cotter
| and clevis pin. |
|
|
3. | Parially lift and support piston bottom with one hand. |
| |
4. | Remove thumbscrew by turning | Locate bottom portion of | |
5. | Remove piston top and gasket. | ||
6. | Replace gasket with new gasket. | hose clip to vent tube at | |
7. | Reverse procedure, turn thumbscrew until 2 clicks are felt. | location as shown. | |
| |||
HAIR PIN | THUMBSCREW |
| |
COTTER |
|
| |
|
| PISTON TOP |
|
|
| GASKET |
|
|
| PISTON BOTTOM |
|
NOTE: DO NOT ADD ANY FOREIGN MATERIALS TO THE SEALING SURFACE.