1 TRIM INSTALLATION

Push CAP (1) over the O-RING SEAL (2).

Push ESCUTCHEON HOLDER (3) with lightly greased O-RING SEAL (4) over CAP (1). Attach with the two LONG SCREWS (7) provided.

Attach ESCUTCHEON (5) to ESCUTCHEON HOLDER (3) with the two SHORT SCREWS (8) provided.

Align pins in back of DIAL PLATE (9) with holes in ESCUTCHEON (5) and push DIAL PLATE (9) into place.

 

1

2

3

 

7

 

5

 

EN

 

OB

 

P/

 

TO

GREASE ESCUTCHEON

4

HOLDER O-RING SEAL

 

8

6

2 HANDLE INSTALLATION

2

 

Push TEMPERATURE-CONTROL KNOB (1) (with the red stop on top)

1

3 4

onto KNOB MOUNT (2).

 

Install HANDLE SCREW (3) and tighten with screwdriver.

Push KNOB CAP (4) into TEMPERATURE-CONTROL KNOB (1).

3 TRANSPOSED SUPPLY PIPING OR BACK TO BACK INSTALLATION

Should the hot and cold water supply pipes have been transposed making adjustment impossible, proceed as follows:

Shut off water supply.

Remove handle and rim

Remove check stops and re-install them transposed.

Important note: RED CHECK STOP is now on the right of the mixer body and the BLUE CHECK STOP is now on the left.

Turn the water supply back on and perform the temperature adjustment in step 4.

CHECK STOP

(RED TO BLUE)

CHECK STOP

(BLUE TO RED)

4 TEMPERATURE CALIBRATION

Check that arrow marking B points vertically upwards. If not, push the BLACK CLAMP (1) on the SECURING RING (2) to the right, pull off KNOB MOUNT (3) and reinstall KNOB MOUNT (3) with arrow "B" pointing upwards.

SET HOT LIMIT STOP

4

 

 

The maximum mixed water temperature is set at 109˚F at the factory.

 

 

 

 

 

 

This setting can be changed if desired.

 

 

Remove the TEMPERATURE LIMIT STOP (4) (H shaped Black Plastic part). Reinstall it at the desired notch as indicated in the diagram to limit the maximum mixed water temperature to 104˚F or 112˚F.

For 100˚F adjustment, turn the water supply on. Turn KNOB MOUNT (3) until the spout temperature is 100˚F. Check that arrow marking A on the KNOB MOUNT (3) still points upward after adjusting the thermostat to 100˚F. If not, pull out the RED LOCKING DEVICE (5). Remove KNOB MOUNT (3) without turning by sliding out as indicated by the arrow.

Reinstall the KNOB MOUNT (3) so that the arrow marking A points upwards. Reinstall RED LOCKING DEVICE (5).

ARROW

1

"B"

 

 

ARROW

 

"A"

104

 

109

3

112

 

2

5

5 OPERATING THE VALVE

1

If the system is delivering all Hot or all Cold and no mixed water the pipes are probably transposed.

If a temperature over 100˚F is desired, pull the RED STOP BUTTON (1) away from the body of the MIXER UNIT and turn the TEMPERATURE KNOB.

This will increase the mixed water temperature up to the maximum limit previously selected in step 4.

M 9 6 8 6 8 2

Page 1 Page 3
Page 2
Image 2
American Standard T203.730 Trim Installation, Handle Installation, Transposed Supply Piping or Back to Back Installation
Page 1 Page 3

T203.730 specifications

The American Standard T203.730 is a versatile and technologically advanced bathroom fixture designed to enhance the bathroom experience. This bathroom faucet is notable for its blend of style, functionality, and sustainability, making it a popular choice among homeowners and designers alike.

One of the main features of the T203.730 is its elegant design. The faucet boasts a contemporary aesthetic that complements a variety of bathroom decors, from modern to traditional. Its sleek lines and polished finish not only contribute to its visual appeal but also make it easy to clean and maintain. Available in different finishes, including chrome and brushed nickel, the T203.730 can easily be integrated into any bathroom setting.

Equipped with innovative technologies, the American Standard T203.730 offers exceptional performance. It uses the brand's proprietary EcoAdvance technology, which ensures that the faucet delivers a strong, steady water flow while minimizing water consumption. This makes the T203.730 an environmentally friendly option that helps homeowners save on their water bills without sacrificing performance. The faucet is designed to meet Watersense certification standards, using at least 20% less water than the industry standard.

The T203.730 also features an intuitive single-handle design, providing effortless control over water temperature and flow. This ergonomic design allows users to adjust the water setting smoothly, ensuring a comfortable and convenient experience. The valve mechanism is engineered for durability, allowing for extended use without the common issues of leaks or drips.

In terms of installation, the T203.730 has been designed for easy setup, fitting standard 3-hole sinks. The durable construction is made to withstand daily wear and tear, ensuring long-term reliability. Additionally, the faucet can be paired with various American Standard bathroom collections, allowing for cohesive design throughout the space.

In summary, the American Standard T203.730 bathroom faucet combines elegant design, innovative technology, and eco-friendly features. With its efficient water usage, user-friendly controls, and durable construction, it represents a significant upgrade for any bathroom, appealing to those who value both style and sustainability.
Top Page Image Contents