2 VALVE TRIM
Place the ESCUTCHEON SEALS (1) over the VALVE BODIES (2).
Thread the VALVE ESCUTCHEONS (3) into the VALVE BODIES (2). Align the HANDLE STEM (4) with the SLEEVE (5) as necessary. Thread the VALVE ESCUTCHEON (3) into the BODIES (2) until the ESCUTCHEON (3) contacts the finished deck.
3
4
1
5
2
3 INSTALL HANDLES |
|
|
|
LEVER HANDLE |
| CROSS HANDLE |
|
|
|
| |
Turn VALVE into OFF position. |
| Turn VALVE into OFF position. | 6 |
Push ADAPTER (1) into HANDLE (2) | 5 | Push ADAPTER (1) into | 4 |
in a way that the male square on the | 3 | HANDLE BASE (2). |
|
ADAPTER (1) fits in the female square | 5 | ||
of the HANDLE (2). |
| Push HANDLE BASE (2) | |
|
|
| |
Push HANDLE (2) and ADAPTER (1) |
| and ADAPTER (1) onto | 2 |
onto VALVE STEM (4). | 2 | VALVE STEM (3). | |
|
|
| |
Check alignment, if not satisfactory aligned; |
| Push CROSS (4) onto | 1 |
Push out ADAPTER (1) carefully. | 1 | ADAPTER (1). | |
|
| ||
| Assemble and tighten |
| |
Turn ADAPTER (1) either 45˚ or 90˚ |
| 3 | |
so that male square on ADAPTER (1) |
| HANDLE SCREW (5). | |
catches different female square in | 4 | Push INDEX CAP (6) in |
|
HANDLE BASE (2). |
|
| |
Assemble and tighten HANDLE |
| top of HANDLE (4). |
|
|
|
| |
SCREW (3). |
|
|
|
Push INDEX CAP (5) in top of HANDLE (2).
4 |
| 5 | SERVICE |
| 3 | 1 |
| TESTING |
|
| 2 |
| |
|
|
| To change the direction of handle rotation |
|
| |
| Turn the HOT HANDLE (1) clockwise and the |
| Turn off the water supplies |
|
|
|
|
|
|
| 4 |
| |
| COLD HANDLE (2) counterclockwise to the |
| Turn HANDLE (1) to the off position. |
| ||
| off position. |
| Remove the INDEX CAP (2) and the HANDLE |
| ||
|
|
|
| |||
| Unscrew and remove the SPOUT END (3). |
| SCREW (3). Pull the HANDLE BASE (4) off and |
| ||
| Slowly turn on the water supplies. |
| remove ADAPTER (5). |
| 5 |
|
|
| Unscrew the VALVE ESCUTCHEON (6). |
|
| ||
|
|
|
|
| ||
| Operate the HANDLES (1, 2) to flush water |
| Unscrew the VALVE LOCK NUT (7) and | 6 |
| |
| lines thoroughly. Check SPOUT (4) connection |
|
| |||
| for leakage. |
| remove. A 17mm deep socket is required. |
|
| |
|
|
|
|
|
| |
| Turn the Handles off. Replace the SPOUT |
| Remove the CARTRIDGE (8) by |
| 90$ |
|
|
| pulling up on the SLEEVE (9). |
| 7 |
| |
| END (3). |
| 12 |
| ||
|
|
| Remove the SCREW (10) | 11 10 |
| |
| 2 |
| from the CARTRIDGE (8). |
|
| |
|
| Remove the SPRING CLIP (11). |
|
|
| |
|
|
|
| 9 |
| |
|
|
|
|
|
| |
|
|
| Remove the STOP WASHER (12). |
|
| |
| 3 |
| Turn it 90˚ and replace. |
|
|
|
|
| Replace the SPRING CLIP (11). |
| 8 |
| |
|
|
|
|
| ||
1 |
|
|
|
|
| |
|
| Reverse the above steps to |
|
|
| |
|
|
|
|
|
| |
| 4 |
| reassembly the components. |
|
|
|
|
|
| If the spout drips, operate the handles several |
| ||
|
|
| times from the off to the on position. Do not |
| ||
4 EverClean™ Finish Care Instructions |
| force - the handles only turn 90˚ |
|
| ||
|
|
|
|
| ||
American Standard’s EverClean finish will wipe clean with a soft, dry cloth. A soft cloth with clean water may also be used, if desired. No additional cleaning products are required.
DO NOT USE: Soaps, acid, polish, abrasives, harsh cleaners, or a cloth with a coarse surface. M968655 Rev. 1 . 1
