AMX quick start AutoPatch Octaire Distribution Matrix, Quick Start Guide, Overview

Quick Start Guide

AutoPatch Octaire Distribution Matrix

Overview

The Octaire Distribution Matrix is a fixed system consisting of a single video or audio enclosure or multiple video enclosures with or without audio in a fixed input/output range. Because the Octaire is available in various fixed sizes, the illustrations in this guide may differ from the model(s) you purchased. The Octaire Instruction Manual contains complete documentation for this product (including individual signal specifications); see the AMX AutoPatch CD or visit www.amx.com.

Note: A label above the power receptacles on video enclosures indicates the signal

type: STD = standard video, UWB = ultra-wideband video, and SYNC = HV sync.

Y/c signals, 3-component signals (Y/Pb/Pr or RGsB), and RGBHV signals require a BNC connection on each video enclosure. The example in FIG. 3 shows three BNC cable connectors attached to corresponding connectors on three enclosures for routing a 3-component signal through Input 1. The first enclosure has a control panel.

Enclosure 1 Enclosure 2 Enclosure 3

General Specifications

Specifications

Approvals	CE, UL, cUL
AC Power	100 to 240 VAC single phase (50 to 60 Hz)
	3.3 A @ 115 VAC max.; 1.6 A @ 230 VAC max.
Power Consumption (max.)	260	Watts per enclosure
Power Consumption (typical)	120	Watts per enclosure, fully loaded

Y

Pb

Pr Video signal type label

Note: Start with the enclosure with the control panel for the first video component type (e.g., R for RGBHV). Link the rest of the enclosures according to the Connector Guide and signal type labels. The audio enclosure is last.

Thermal Dissipation (max.)	887 BTU/hr.
Thermal Dissipation (typical)	409 BTU/hr., fully loaded enclosure
Operational Temperature	32° to 113° F (0° to 45° C)
Humidity	0 to 90% non-condensing
Enclosure Dimensions	12 in. (30.5 cm) depth
	18.9 in. (48 cm) width with mounting ears
	17.4 in. (44.2 cm) width without mounting ears
	6.95 in. (17.65 cm) height, 4 RU
Weight	Approximately 20 lbs. (9.07 kg) per loaded enclosure
	Approximately 24 lbs. (10.89 kg) packaged for shipping

Installation

ESD Warning: Avoid ESD (Electrostatic Discharge) damage to sensitive components; be sure you and the enclosure(s) are properly grounded before touching any internal materials.

Rack Mounting – standard EIA 19 in. (48.26 cm) rack

To rack mount an Octaire enclosure:

1. Attach rack ears (4 screws each); see FIG. 1.

2. Place the Octaire in the rack, leaving a minimum of one empty rack unit above and below (required); three empty rack units are recommended.

3. Secure enclosure to rack with screws.

Tip: When placing in the rack, keep in mind the optimal viewing angle for a control panel is eye level.

FIG. 1 Attach rack ears

Linking Multiple Enclosures (if applicable)

For multi-enclosure systems, use the link cables provided. Link from the bottom Link port (RJ-45) on one enclosure to the top Link port on next enclosure in a daisy chain. Check the signal type label on the rear of each enclosure (see the Note on FIG. 3).

Start with primary enclosure (with control panel)

Important: An Octaire system can only be linked in its own isolated network.

Crossover cable

3 ft. (0.9 m) provided

Link to additional enclosures as required

FIG. 2 Use Link ports to link enclosures with cable provided

FIG. 3 Multiple BNC connectors are required for all video signals except composite

Stereo Audio Connectors – 5-Term

Stereo audio connections use 5-position terminal blocks; they can be wired for balanced (differential) audio or unbalanced (single-ended) audio (FIG. 4).

FIG. 4 Balanced audio Unbalanced audio

Note: When using a shielded twisted-pair cable, connect the shield (ground) at one end only (recommend receiving end) to minimize low frequency noise (FIG. 5).

Source and destination devices will require either balanced (differential) or unbalanced (single-ended) connections. More than one of the options shown in FIG. 5 can be used in the same system.

FIG. 5 Options for source-to-Octaire-to-destination 5-Term wiring

Attaching Input & Output Cables/Wires

For testing, attach the input and output connectors for the first source and the first destination. Each system comes with a Connector Guide and “Signal Color-Band” kit. Multiple BNC connectors are required for all video signals except composite (FIG. 3).

Video Connectors – BNC

All video connectors are BNC. Octaire systems with video contain one or more of the following types of video enclosures:

•1 or 2 standard video enclosures – support composite or Y/c signals.

•3 ultra-wideband enclosures – support three-component or the R, G, and B components of an RGBHV signal.

•2 digital sync enclosures – support the H/V sync part of an RGBHV signal.

Applying Power & Control Startup

Important: We recommend attaching all power cords to one or two surge protectors (top outlets together and bottom ones together) and/or an AC line conditioner(s).

When power is applied, the Power indicator on the front of the panel illuminates green to indicate the redundant power supplies are both working. If only one power supply is working, the Power indicator illuminates red (check power connections and switches).

To apply power:

1.Attach power cords (FIG. 6, top of next page) and plug into power source (turn on power source if necessary). Press the “l” side of both power switches on the enclosure(s).

The Power Indicator on the front of the enclosure illuminates a constant green.

2.Apply power to the source and destination devices.