
Installation Guide
Overview
Wall Mount panels (NXDs) are contained within a metallic outer housing (back box). This back box is not removed when installing the NXD into a
The
Specifications
CB-TP17 (FG034-10) Specifications
Dimensions (HWD) | • 13.55" x 17.07" x 3.49" |
| • 34.43 cm x 43.38 cm x 8.85 cm |
|
|
Included | |
Accessories | • 4 Phillips |
| • 4 Phillips |
|
|
Certifications | • cTUVus Listed |
|
|
WARNING: INSTALLER, LEAVE A GAP BETWEEN THE STUD AND ROUGH- IN BOX TO ACCOMMODATE THE DRYWALL/SHEETROCK.
This gap allows the installation of the drywall/sheetrock after the
Note: The most important thing to remember when mounting this
Pre-Wall Installation of the CP-TP17 Rough-In Box
1.Measure the distance between the inside of the two selected stud beams. Most beams have a distance of about 14" to 16". This is too narrow to accommodate the 17.072" (43.36 cm) wide
2.Determine whether one or both of the selected stud beams must be notched (FIG. 2). The determining factor is the flush alignment of the mounting tabs along the outside of the
Installing the 17" panel within a CB-TP17 Rough-In Box
The
1.Remove the magnetic faceplate/bezel (A in FIG. 1) from the main NXD unit (B in FIG. 1) by gripping the faceplate and pulling with gentle outward force.
2.Verify the incoming
3.Connect all data and power wiring connectors to their corresponding locations along the side of the
•Verify the terminal end of the power cable is not connected to a power supply before plugging in the
•The USB connectors can be from either a USB extension cable, or a wireless USB RF transmitter.
Note: Don’t disconnect the connectors from the touch panel. The unit must be installed with the attached connectors before being inserted into the CB.
4.Test the incoming wiring by connecting the panel connections to their terminal locations and applying power. Verify the panel is receiving power and functioning properly to prevent repetition of the installation.
5.Disconnect the terminal end of the power cable from the connected PSN power supply.
6.Carefully slide the main NXD unit (B in FIG. 1) into the
7.Insert and secure four securing #8
8.Replace the magnet faceplate (A in FIG. 1) back onto the main NXD unit. Make sure to align the Microphone, Light, and PIR Motion sensor locations to their respective openings on the front bezel/faceplate.
9.Connect the terminal
10.Reconnect the terminal power connector on the PSN and apply power.
3.Cutout the notched beam using a height of 13.554" (34.43 cm) (as shown in FIG. 2) and a depth equal to the thickness of the drywall.
Note: The determining factor in the depth of the cut into the beam is the thickness of the drywall. The mounting tabs MUST BE FLUSH against the drywall and therefore, the depth of the notch depends on that thickness.
4.Insert one side of the
5.Install and secure a shorter horizontal beam below the
6.Fasten the
7.Insert a perpendicular block between the
8.Secure the perpendicular block to the
9.Fasten the
10.Remove any necessary wiring knockouts from the (optional)
11.Thread the incoming
Do not use these | Stud | |
tabs to mount | ||
Support block | ||
the | C - Optional | |
Four #8 | ||
Mounting Screws | ||
| ||
(not included) |
| |
secure the NXD to |
| |
|
|
| Mounting Tab |
A - Faceplate | B - Main NXD unit consists of |
(bezel) | the touch panel and backbox housing |
|
FIG. 1 Wall Mount panel installation configuration of a CB-TP17
12.Install the drywall/sheetrock before inserting the main NXD unit into the