Installation Guide
DAS-TAMP4/8-SIG Tango Amplifiers
Overview
Where more than one pair of speakers is required in a zone, Tango Amplifiers provide the extra power needed to drive up to 4 additional speaker pairs (FIG. 1).
Light Bar (power status)
Status Indicator LED
From Controller: | SWT input port (connects to an Tango Audio |
| Controller) |
|
|
To Keypad: | SWT output port (connects to Matrix keypad or |
| interface) |
|
|
Dimensions (HWD): | Including feet and rear connectors: |
| • 3 1/16” x 17” x 13 1/2” |
| • 7.68cm x 43.18cm x 33.52cm |
|
|
Weight: | 25.75 lbs (11.68 kg) |
|
|
Included Accessories: | • Power cord |
|
|
Other AMX Equipment: | • |
|
|
To Keypad
From Controller
Zone Outputs (4 or 8)
Power Switch & Receptacle
FIG. 1 Tango Amplifiers
Tango Amplifiers provide extra output power to multiple pairs of speakers driven from one zone.
•The
•The
Product Specifications
Tango Amplifiers - Product SpecificationsModels Available: | • |
| Amplifier (120 V) |
| • |
| Amplifier (120 V) |
|
|
Configuration: | • Modular Design - configurable in single pairs up to |
| 4 stereo pairs (8 channels). |
| • Stackable up to 3 Tango Amplifiers or 12 stereo |
| pairs (24 channels) |
|
|
Stereo Output: | • Dual mono amplifier stage design |
| • 60 watts per channel |
| • THD+N at 1 Khz continuous .006%@ 8 Ohms |
| • Each Tango amplifier is capable of providing 480 |
| watts @ 8 Ohms |
|
|
Control Options: | • Metreau |
| keypads |
| • |
|
|
Power: | • 750W max (Average usage = 250W). |
| • High current Torroidal power supply |
|
|
Front Panel Components: |
|
|
|
Light Bar | • Blue light bar indicates power status. |
|
|
Status LED | • Blue LED lights when active |
|
|
Rear Panel Components: |
|
|
|
Power Switch & Receptacle | The master power switch will remain in the ON posi- |
| tion normally. |
|
|
Output | SWT connectors provide direct connection to |
| speakers. |
|
|
Rack-Mounting
Tango units occupy two rack spaces in a standard 19" equipment rack. Rack mounting brackets are supplied with the optional
Note: Exercise extreme care when lifting or moving Tango units within the rack to avoid injury. It is recommended that you seek the assistance of another person when rack mounting Tango units.
1.Attach the rack mounting brackets to each side of the Tango unit using the four screws
Note: To prevent injury the Tango unit must be securely attached to the rack in accordance with the installation instructions. ALWAYS use the spe- cial rack mount brackets supplied and high quality fixing screws to ensure the Tango unit is installed in the rack correctly.
2.Place the Tango unit in the equipment rack and hold steady.
3.Secure the Tango unit in the rack using the mounting holes.
Note: DO NOT stand other units directly on top of the Tango unit when it is rack mounted, as this will place excessive strain on the mounting brackets.
Ventilation
To ensure that the rack enclosure is adequately ventilated, there must be a minimum of 3" all around the Tango unit.
Sufficient airflow must be achieved (by convection or
Speaker Wire Technology (SWT)
Speaker Wire Technology (SWT) allows both data and audio signals to travel over the same four conductor wire. This remarkable technology removes the need for control wire since the control and audio signals are shared on the same wire. The reliability and simplicity of this system has been proven for years. AMX Distributed Audio is the only company that offers a “retrofit solution”, one which allows the replacement of volume controls with AMX Distributed Audio keypads and Controllers, giving full control over the sources. Additionally, the versatility of SWT also allows AMX Distributed Audio products to be connected where the control wire has been run separately from the speaker cable.
Cabling Instructions
CAUTION: Be sure to check for any wiring restrictions required by the electrical code in your area.
This installation uses low voltage cabling similar to telephone and alarm wiring, and as such does not commonly have very many restrictions on their installation. However rules may vary in different regions.
Cable Type
The Tango Amplifier is cabled using standard