Quick Start Guide
Mio Modero DMS Keypad metallic
Overview | Installation |
The Mio Modero DMS device family provides a wide range of control capabilities in the form of user specified buttons that are functional yet recherché.
Mio Modero DMS keypads are equipped with an LCD menu display with 8 pushbuttons for navigation and menu selection.
Note: To avoid any damage to the electronic component, installation must be performed in an ESD safe environment. The device and conduit box must have an Earth ground.
The installation section addresses the mounting and wiring of the Mio Modero DMS. After you have completed the installation you must consult Necessary Device Setup.
Menu items
Menu Up
Menu select pushbuttons
Menu Down
Rear Components
The rear components of the Mio Modero DMS (FIG. 2) are as follows:
Ethernet Port (PoE)
(Front View)
Magnetic Posts
FIG. 1 Mio Modero DMS Device Family
Specifications
Mio Modero DMS (FG2408-01XX) Specifications
Power 12 VDC / PoE: |
|
| |
Maximum power consumption (PoE): | • | 5.5 Watts | |
Maximum startup (rush) current (PoE): | • | 150 mA @ 50 VDC | |
Maximum continuous current (PoE): | • | 100 mA @ 50 VDC | |
Maximum power consumption (DC): | • | 5.0 Watts | |
Maximum startup (rush) current (DC): | • | 525 mA @ 13.5 VDC | |
Maximum continuous current (DC): | • | 350 mA @ 13.5 VDC | |
|
|
| |
Front Panel Components: | • | LCD display | |
| • | 8 pushbuttons | |
|
|
| |
Rear Panel Connectors: | • | Ethernet Port (PoE) | |
| • | ||
| • | 4 Magnetic Posts | |
| • | Ground wire | |
|
|
| |
Dimensions (HWD): | • 6.25 (158.8 mm) x 3.50 (91.4 mm) x 3.93 (99.7 mm) | ||
(inside of conduit box) | |||
|
| ||
|
| ||
Supported Fonts: | Only True Type Fonts | ||
|
|
| |
Weight (range): | • | Device | |
|
|
| |
Operating Environment: | • | Operating Temperature: 0° to 40° C (32° to 104° F) | |
| • Storage Temperature: | ||
|
| ||
Mounting: | The Mio Modero DMS is installed in one of three ways: | ||
| • | ||
| • Expansion clips for pressure mounting | ||
| • No tabs for brick and mortar mounting | ||
|
| ||
Available Color Schemes: | Gold (GL), Silver (SL) | ||
|
|
| |
Included Accessories: | • | ||
| • | Conduit box | |
| • | Mounting kit | |
|
|
| |
Other AMX Equipment: | • | ||
|
| Over Ethernet | |
|
|
| |
Dynamic Menu System
Using the KeypadBuilder application available for download from www.amx.com, the Mio Modero DMS is programmed with a Dynamic Menu System (DMS) that is navigated via the 8 pushbuttons and LCD display area. See the KeypadBuilder Instruction Manual for more information on programming Mio Modero DMS devices.
3.5 mm
(female) connector
FIG. 2 Mio Modero DMS Rear Components
Connections and Wiring
The Mio Modero DMS device is powered either via 12VDC or Power over Ethernet (PoE). If both the 12 VDC and PoE power sources are connected, by default the device draws power from the 12 VDC. If the 12 VDC source is disconnected, the PoE automatically supplies power after a device reboot.
Note: Do not connect power to the Mio Modero DMS until the wiring is complete.
Preparing captive wires for the 2-pin 3.5 mm mini-Phoenix connector
You will need a wire stripper, and
1.Strip 0.25 inch (6.35 mm) of wire insulation off all wires.
2.Insert each wire into the appropriate opening on the connector according to the wiring diagrams and connector types described in this section.
3.Turn the screws clockwise to secure the wires in the connector.
Note: Do not
Using the PSN NetLinx connector for power
The PWR and GND wires from the 12 VDC power supply must be connected to the corresponding location on the
1.Insert the PWR and GND wires on the terminal end of a PSN
2.Tighten the clamp to secure the two wires.
3.Verify the connection of the
Using the Ethernet port for power (PoE)
Connect your CAT5/CAT6 Ethernet cable to the port shown in FIG. 2. (See the Mio Modero DMS & Mio Modero DMS Pinnacle instruction manual for an illustration and cable pinouts).
