Component Input at Display Device
1.Attach the Component cables (normally green, blue and red) to the Y (green), Pb (blue) and Pr (red) connectors on the
2.Run the other end of the Component cable to the Component connectors (nor- mally green, blue and red) on the display device. Connect firmly.
3.If appropriate connect audio to the audio connectors on the
Audio & Video Formats/Resolutions/Distance
Audio & Video Formats/Resolutions/Distance
Class | Format | Name | Distance |
Composite | 720x480 | NTSC | 300 m / 1000’ |
| 720x576 | PAL | 300 m / 1000’ |
Component | 720x480 | 480p | 300 m / 1000’ |
| 720x576 | 576p | 300 m / 1000’ |
| 1280x720 | 720p | 300 m / 1000’ |
| 1920x1080 | 1080i | 300 m / 1000’ |
| 1920x1080 | 1080p | 300 m / 1000’ |
VGA | 640x480 | VGA | 300 m / 1000’ * |
| 800x600 | SVGA | 300 m / 1000’ * |
| 1024x768 | XGA | 300 m / 1000’ * |
| 1280x1024 | SXGA | 300 m / 1000’ * |
| 1600x1200 | UXGA | 300 m / 1000’ * |
| * When using VGA modes with audio enabled, the maximum | ||
| cable distance is approximately 200 m / 650’. | ||
Note: The maximum distances indicated above are not absolute, but are recommended distances that have been tested to deliver video at the specified resolutions, without significant signal degradation. In particular, lower resolutions (640 x 480, 720 x 480 and 800 x 600) can often be delivered significantly further than what is indicated in the table. Refer to the UDM Hub’s Operation/Reference Guide for additional details on maximum cable distances.
Video Compensation
Video at the Receive end can be compensated using three main methods;
•Using the UDM Hub’s WebConsole
•Using the
•Using a hyper terminal session via the serial connector on the
Connecting an External IR Receiver Module
If passthrough mode (where a device such as a DVD or VCR can be controlled via a
Additionally, if the
Connecting the UDM-RX02 Receiver to the UDM Hub
The RJ45 port on the front panel of the
1.Connect a standard Cat5/6 Ethernet cable to the RJ45 port labelled UDM on the front panel of the UDM hub.
2.Connect the other end of the Ethernet cable to the RJ45 port labelled UDM Hub on the rear panel of the
Note: Ensure the UDM Hub port the RX02 is attached to is configured correctly within the Hub’s configuration software. Also ensure the correct Audio Type (Analog L/R, S/PDIF, or None) is selected for the relevant input.
UDM HUB Port LEDs
2LEDs are visible at the UDM Hub port (on the
•Green – Connection to
•Amber – Power (as well as comms if uploading protocols etc. the Amber LED may flicker).
Powering on the UDM-RX02
The
To connect the
To power down the
Note: Disconnecting the optional power supply will not power down the
System Overview
FIG. 3 provides a basic system diagram representing a
| DVD | DSS |
|
Video Out | Audio Out | Video Out | Audio Out |
| Video In | Audio In | Video In |
|
| Audio In | |||||||
|
|
|
| UDM Hub |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| ||
Ethernet |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| ||
(network |
|
|
|
|
|
|
|
|
|
|
| Cat5 | |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| UDM Receiver |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Video Out | Audio Out |
|
|
|
|
|
|
|
|
Video In | Audio In |
| Display |
FIG. 3 UDM System Diagram
Additional Documentation
Refer to the
For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s). | |
| |
2/08 |
|
©2008 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX. |
|
AMX reserves the right to alter specifications without notice at any time. |
|
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com |
|
