Anritsu MP1763C iii

For Safety

iii

WARNING

1. ALWAYS refer to the operation manual when working near locations

at which the alert mark shown on the left is attached. If the advice in

the operation manual is not followed there is a risk of personal injury

or reduced equipment performance. The alert mark shown on the

left may also be used with other marks and descriptions to indicate

other dangers.

2. IEC 61010 Standard

The IEC 61010 standard specifies four categories to ensure that an

instrument is used only at locations where it is safe to make

measurements. This instrument is designed for measurement

category I (CAT I). DO NOT use this instrument at locations

specified as category II, III, or IV as defined below.

Measurement category I (CAT I):

Secondary circuits of a device that is not directly connected to a

power outlet.

Measurement category II (CAT II):

Primary circuits of a device that is directly connected to a power outlet,

e.g., portable tools or home appliance.

Measurement category III (CAT III):

Primary circuits of a device (fixed equipment) to which power is

supplied directly from the distribution panel, and circuits running from

the distribution panel to power outlet.

Measurement category IV (CAT IV):

Building service-line entrance circuits, and circuits running from the

service-line entrance to the meter or primary circuit breaker

(distribution panel).

3. To ensure that the instrument is grounded, always use the supplied

3-pin power cord, and insert the plug into an outlet with a ground

terminal. If power is supplied without grounding the equipment,

there is a risk of receiving a severe or fatal electric shock.

Contents

Main ii Safety Symbols Symbols used in manual Safety Symbols Used on Equipment and in Manual DANGER WARNING CAUTION iii iv v vi vii Equipment Certificate Anritsu Warranty Anritsu Corporation Contact viii Notes On Export Management Lifetime of Parts FOR CALIFORNIA USA ONLY Page x CE Conformity Marking CE marking 1. Product Model 2. Applied Directive 3. Applied Standards C-tick Conformity Marking xii Power Line Fuse Protection I Composition of MP1763C Operation Manuals II Title of Contents SECTION 3 DESCRIPTION OF PANELS AND CONNECTORS ............................. 3-1 SECTION 4 OPERATING INSTRUCTIONS ............................................................... 4-1 Page Page Page 1-2 1.2 Specifications 1-3 whichever is larger 1-4 1-5 1-6 Section 1 GENERAL 1-7 * When OPTION 03 is installed, there is no 1/8 output. 1-8 1.3 Composition 2-1 SECTION 2 PREPARATIONS 2.1 Environmental Conditions of Installation Site 2.2 Safety Measures 2-2 2.3 Power Connection 2.3.1 Power Requirements 2.3.2 Connecting the Power Cord 2-3 2.4 Damage Prevention Measures Page Page Section 3 DESCRIPTION OF PANELS AND CONNECTORS PULSE PATTERN GENERATOR MP1763C 0.05 - 12.5GHz INTERNAL CLOCK (OPTION.01) PATTERN MEMORY 3.1 FRONT PANEL 3-2 3-3 3-4 3.2 REAR PANEL Section 3 DESCRIPTION OF PANELS AND CONNECTORS !! Nameplate 3-5 Page Page 4-2 4-3 4.2 Generation Pattern Setting 4-4 4.2.1 Logic modification 4.2.2 Alternate pattern setting 4-5 4-6 4.2.3 DATA pattern setting 4-7 4.2.4 ZERO SUBSTITUTION 4-8 4.2.5 Pseudo random pattern setting 4-9 4.2.6 ERROR addition 4-10 4.2.7 Tracking 4-11 4.2.8 Pattern SYNC. position 4-12 4-13 4.3 Output Interface 4-14 4.3.1 DUMMY terminal voltage switching 4-15 4.3.2 Amplitude, offset, and delay setting 4-16 The output waveform is as follows for any of the above three settings: OFFSEET 2 V If VOH is changed to VTH: OFFSEET 1.5 V 4-17 4.3.3 Duty adjustment 4.3.4 Cross point adjustment 4-18 4.3.5 Offset voltage setting range Page Page Page Page 4-23 4.4.1 File save 4-24 4.4.2 File recall 4.4.3 Disk formatting 4-25 4.4.4 File deletion 4.4.5 Error messages 4-26 4.4.6 Floppy disk 4.4.7 Floppy disk precautions 4-27 4.5 Parameters initialization 4-28 4.6 Functions of the FUNCTION Switch 5-1 SECTION 5 PRINCIPLES OF OPERATION 5.1 Pseudorandom Pattern (PRBS Pattern) 5-2 1 2 3 4 5 6 5-3 5.2 Pattern Synchronized Output Period 5.2.1 Pseudorandom pattern 5.2.2 Programmable pattern 5-4 5.3 Bit shift for Alternate A/B select timing 6-1 SECTION 6 PERFORMANCE TEST MEMORY MEMORY 6.1 Test Equipment 6.2 Error Measurement 6-2 Section 6 PERFORMANCE TEST MEMORY 6.3 Test Method Output DATA amplitude 0.5 Vp-p offset 0 Vp-p CLOCK amplitude 0.5 Vp-p offset 0.0 V Delay 0 ps 6-3 6.5 Check Items Check the 1/8 SPEED output with the connection shown at the below. !! Check all the outputs with the connections DATA1 DATA2 - - - DATA8. Fig. 6.3-2 Connection of rear panel Page 7-1 SECTION 7 MAINTENANCE 7.1 Daily Maintenance 7.2 Storage Precautions 7.3 Transportation Page 8-1 SECTION 8 TROUBLESHOOTING AND REPAIR 8.1 Before Considering Trouble Page A-1 APPENDIX A PERFORMANCE TEST REPORT SHEET Page INDEX-1 INDEX