2.2LOAD TRANSIENT RESPONSE (STEP LOAD) / RÉGIME TRANSITOIRE DE CHARGE / LASTÜBERGANGSVERHALTEN (SCHRITTLAST) / RISPOSTA ALLE VARIAZIONI DI CARICO (CARICO A GRADINO) / RESPUESTA A TRANSITORIOS DE CARGA (CARGA REPENTINA)

Step load changes of up to 20% of full load, while other loads remains constant within the rating. The load waveform shall be a square wave with the slope of the rise and fall at 1A/us and the frequency shall be from 10Hz to 1 kHz. The DC output voltage will stay within regulation during the step load changes

Des changements de charge incrémentiels jusqu'à 20% de la pleine charge, tandis que les autres charges restent constantes dans les limites des valeurs nominales. La courbe de charge devra être une onde carrée avec la pente de montée et de descente à 1A/µs et la fréquence devra être comprise entre 10Hz et 1kHz. La tension de sortie c.c. restera dans les limites de régulation durant les changements de charge incrémentiels

Schrittlaständerungen von bis zu 20% bei voller Belastung, während andere Lasten innerhalb der Nennwerte konstant bleiben. Lastwellenform: Rechteckwelle mit Neigung bei Anstieg und Abfall von 1A/us. Frequenz von 10Hz bis 1kHz. Ausgangsspannung (Gleichstrom): zwischen Schrittlaständerungen innerhalb des Regulationsbereichs

I carichi a gradino apportano variazioni fino al 20% rispetto al pieno carico, mentre altri carichi restano costanti entro i valori nominali. La forma d'onda del carico deve essere un'onda quadra con la pendenza di salita e di discesa di 1A/usec e la frequenza andrà da 10Hz a 1kHz. La tensione d'uscita CC resterà entro la regolazione durante le variazioni dei carichi a gradino

Cambios repentinos de la carga de hasta el 20% de la carga total, mientras otras cargas permanecen constantes dentro del régimen. La onda de la carga debe tener forma cuadrada con la pendiente de subida y bajada a 1A/us y la frecuencia debe ser de entre 10Hz y 1kHz. La tensión de salida de CC permanecerá en lo regulado durante los cambios repentinos en la carga

2.3OVERSHOOT / DÉPASSEMENT / ÜBERSCHWINGEN / SUPERAMENTO / SOBREIMPULSO

Overshoot at turn on shall be less than 10% of the nominal output voltage

Le dépassement à la mise sous tension doit être inférieur à 10% de la tension de sortie nominale

Das Überschwingen beim Einschalten muss unter 10% der Nennausgangsspannung liegen

Durante l'avvio l'eccesso di correzione deve essere minore del 10% rispetto alla tensione nominale d'uscita

El sobreimpulso de encendido debe ser inferior al 10% de la tensión de salida nominal

19

Page 19 Page 21
Page 20
Image 20
Antec 500 user manual
Page 19 Page 21

500 specifications

The Antec 500 is a popular mid-tower chassis that has garnered a strong reputation among PC builders and gamers alike. This case is designed to accommodate a variety of components while ensuring optimal airflow and thermal performance. One of its standout features is its spacious interior, which supports a wide range of graphics cards and cooling solutions. Gamers looking to build a high-performance rig will appreciate the flexibility that the Antec 500 provides.

One of the key characteristics of the Antec 500 is its thoughtful layout. The case supports multiple drive configurations, allowing users to install up to three 5.25-inch optical drives and four 3.5-inch hard drives. This versatility is complemented by tool-less drive bays, making the installation process simpler and more efficient. Additionally, the chassis includes ample cable management options that help maintain a clean and organized build. This is particularly important for enhancing airflow, as a tidy setup can significantly reduce obstructive airflow that leads to increased temperatures.

Cooling capability is a critical aspect of any gaming case, and the Antec 500 excels in this area. It features two pre-installed 120mm fans – one in the front and one in the rear – promoting efficient airflow throughout the chassis. Users can expand their cooling options further by adding additional fans in various locations, including the side panels. The strategically placed fan mounts ensure that both intake and exhaust air flows are optimized, keeping components cool even during intense gaming sessions.

In terms of aesthetics, the Antec 500 presents a sleek design that appeals to both gamers and professionals. The front panel includes a mesh design that not only enhances airflow but also adds a modern touch to the overall look. The case is available in different finishes, including black, which complements any gaming setup or workstation.

Another notable feature is the ease of access to ports and connectors. The Antec 500 incorporates a user-friendly front panel layout with USB ports, audio jacks, and a power button conveniently positioned for easy reach. This makes it effortless to connect peripherals without having to stretch around the back of the case.

In summary, the Antec 500 is a well-rounded mid-tower case designed for efficiency, expandability, and style. With its robust cooling solutions, spacious layout, and aesthetic appeal, it’s an ideal choice for gamers and PC enthusiasts seeking a reliable chassis for their builds. Whether you’re assembling a powerful gaming rig or a workstation, the Antec 500 stands out as a solid option in the competitive market of computer cases.
Top Page Image Contents