Using the remote control
CR-389 REMOTE CONTROL
The
TUNER |
|
|
|
|
|
|
|
|
These buttons are used to control tuner functions. |
|
|
|
|
|
|
| |
Note that the FM/DAB lights indicate into which mode | TUNER |
|
|
|
|
|
| |
you are switching the remote control.The lights only |
|
|
|
|
|
| ||
|
|
|
|
|
|
| ||
| FM DAB |
|
|
| Power/Standby |
|
| |
illuminate for five seconds to conserve battery power. |
|
|
|
|
| |||
If neither light is illuminated this does not mean that the remote | MENU | DISP |
| Toggles the amplifier between standby mode and full power | ||||
control is not working! | DAB |
| mode.The power indicator light next to the power button on | |||||
| FM |
|
|
|
|
|
|
|
|
|
|
|
| the front panel is red if the amplifier is in standby, amber while | |||
| the amplifier is powering up (this only takes a few seconds) and | |||||||
(UP and DOWN) |
|
|
|
| green when the amplifier is powered up. | |||
|
|
|
| |||||
Perform the same function as the |
|
|
|
| ||||
buttons on the front |
|
|
|
|
|
|
| |
panel (see page 6). | MODE |
|
| BAND | SP1 and SP2 |
|
| |
|
|
|
|
| ||||
|
|
|
|
|
|
| ||
|
|
|
|
| These buttons allow you to select and deselect the main (SP1) | |||
|
|
| SP1 |
| and secondary (SP2) sets of speakers attached to your amplifier | |||
|
|
|
| (see page 6). |
|
| ||
|
|
|
|
|
|
| ||
ENTER | ENTER |
| SP2 | DISP |
|
|
|
|
|
|
|
|
|
|
| ||
Performs the same function as the ENTER button on the front |
|
|
|
|
|
|
| |
panel (see page 8). |
|
|
|
| DISP (display) |
|
| |
| SEL |
|
|
|
|
| ||
|
|
|
|
| Cycles through the settings ‘Bright’, ‘Off ’ and ‘Dim’.Turning the | |||
SELECT |
|
|
|
| display ‘Off ’ generally gives a slight improvement in sound quality. | |||
|
|
|
|
|
|
|
| |
Performs same function as the SELECT button on the front |
|
|
|
|
|
|
| |
panel. It allows you to use the remote’s volume switch in the |
|
|
|
|
|
|
| |
same way you use the control dial on the front panel – to |
|
|
| Volume and | (mute) |
| ||
adjust various amplifier settings (see page 8). |
|
|
|
| ||||
|
|
| Press + to increase volume or – to decrease the output volume | |||||
Note that pressing + corresponds to turning the |
|
|
| |||||
|
|
| of the amplifier. |
|
| |||
Control knob clockwise, – to anticlockwise. |
|
|
|
|
| |||
|
|
| Press | to mute the speaker connections and preamp outputs. | ||||
| PHONO | AUX | CD | TUNER | ||||
|
|
|
|
| Both tape outputs and the headphone socket remain active. | |||
| AV | DVD | VCR | TAPE | Mute is disabled either by pressing | again, or by adjusting | ||
Source selection buttons | the volume. |
|
| |||||
|
|
|
|
|
| |||
These operate in the same way as the source selectors on the | AMPLIFIER |
| You can use the remote’s volume control in conjunction with | |||||
front panel of your integrated amplifier. |
|
| ||||||
|
| the SELECT button to adjust balance, tone and amplifier settings. | ||||||
|
|
|
| |||||
|
|
|
|
| ||||
|
|
|
| RPT |
|
|
|
|
|
|
| PROG | DISP | CD controls |
|
| |
|
|
|
|
|
|
| ||
|
| CD |
|
| These offer basic control of Arcam CD players | |||
|
|
|
|
|
|
|
| |
|
|
|
|
| NOTE |
|
|
|
|
|
|
|
| Remember to install the two AAA batteries supplied | |||
|
|
|
|
| before trying to use your remote control. | |||
|
|
|
|
| Do not place anything in front of the FMJ badge on | |||
|
|
|
|
| the top left of the CD player (where the IR receiver | |||
|
|
|
|
| is located), or the remote control may not work. | |||
|
| 10 |
|
|
|
|
|
|