Using the remote control
CR-389 Remote Control
The
TUNER |
|
|
|
|
|
|
|
These buttons are used to control tuner functions. |
|
|
|
|
|
|
|
Note that the FM/DAB lights indicate into which mode |
|
|
|
|
|
|
|
you are switching the remote control. The lights only |
| ����� |
|
|
|
| |
illuminate for five seconds to conserve battery power. | �� ��� |
|
|
| Power/Standby | ||
If neither light is illuminated this does not mean that |
|
|
|
| |||
|
|
|
| Toggles the amplifier between standby mode and full | |||
the remote control is not working! |
| ���� | ���� |
| |||
| �� |
| power mode. The power indicator light next to the power | ||||
| ��� |
|
|
| button on the front panel is red if the amplifier is in | ||
|
|
|
|
| |||
| ��� | ���� | ���� | ���� | standby, amber while the amplifier is powering up (this | ||
| only takes a few seconds) and green when the amplifier | ||||||
56 (UP and DOWN) |
|
|
|
| |||
|
|
|
| is powered up. |
| ||
|
|
|
|
|
| ||
These buttons do not apply to the A70. | ���� | ���� | ���� | ���� |
|
|
|
|
|
|
|
|
|
| |
| ���� |
|
| ���� | SP1 and SP2 |
| |
|
|
|
|
|
| ||
|
|
|
|
| These buttons allow you to select and deselect the main | ||
|
|
| ��� |
| (SP1) and secondary (SP2) sets of speakers attached to | ||
ENTER |
|
|
|
| your amplifier (see page 6). | ||
����� |
| ��� | ���� |
|
|
| |
|
|
|
|
| |||
Performs the same function as the ENTER |
|
|
|
|
|
|
|
button on the front panel (see page 6). |
|
|
|
| DISP (display) | ||
| ������ |
|
|
| |||
|
|
|
|
|
|
| |
|
|
|
|
| Cycles through the settings ‘Bright’, ‘Off’ and ‘Dim’. | ||
SELECT |
|
|
|
| Turning the display ‘Off’ generally gives a slight | ||
|
|
|
| improvement in sound quality. | |||
Performs same function as the SELECT button on the |
|
|
|
| |||
|
|
|
|
|
|
| |
front panel. It allows you to use the remote’s volume |
|
|
|
|
|
|
|
switch in the same way you use the control dial on |
|
|
|
|
|
|
|
the front panel – to adjust various amplifier settings |
|
|
|
| Volume and | (mute) | |
(see page 8). |
|
|
|
| |||
|
|
|
| Press + to increase volume or – to decrease the output | |||
Note that pressing + corresponds to turning the |
|
|
|
| |||
|
|
|
| volume of the amplifier. | |||
Control knob clockwise, – to anticlockwise. |
|
|
|
| |||
|
|
|
| Press | to mute the speaker connections and preamp | ||
| ����� | ��� | ����� | �� | |||
| outputs. Both tape outputs and the headphone socket | ||||||
|
|
|
|
| |||
Source selection buttons |
|
|
|
| remain active. Mute is disabled either by pressing | ||
�� | ���� | ��� | ��� | again, or by adjusting the volume. | |||
These operate in the same way as the source |
| ��������� |
| You can use the remote’s volume control in conjunction | |||
selectors on the front panel of your integrated |
|
| with the SELECT button to adjust balance, tone and | ||||
|
|
|
| ||||
amplifier. |
|
|
|
| amplifier settings. |
| |
|
|
|
| ��� |
|
|
|
|
|
| ���� | ���� | CD controls |
| |
|
|
| �� |
| These offer basic controls of Arcam CD players | ||
|
| ������ |
|
|
|
|
English
NOTE: Remember to install the two supplied AAA batteries before trying to use your remote control!
Do not place anything in front of the IR receiver on the left of the A70, or the remote control may not work.
A70