Arcam AVR400 service manual System Control Microprocessors

IC141 also has two sets of I2S data outputs. DA1 is an 8 channel I2S signal (pins 47, 48, 49 and 51) shown as part of the bus DA0(04:07). This feeds the input of the second DSP IC142 (on pins 23, 24, 26 and 27). The system clock is on pin 52 of IC141 and the LR clock on pin 54. These go to pins 29 and 30 of IC142.

DA2 is a stereo I2S output (pin 43 for data, pin 44 for the system clock and pin 46 for the LR clock). This feeds the HDMI board via WF104 and the octal bus switch IC146. The DSP master clock output from pin 9 of IC145 follows the same route. An SPDIF output from pin 35 of IC141 goes directly to pin 12 of WF104.

There is one set of 8 channel I2S outputs from IC142 – DA1 (pins 47, 48, 49 and 51). These form part of the data bus DA0(00:03) where they are routed back to the DACs in IC143 (pins 62, 64, 63 and1 respec- tively). The I2S system clock and LR clock (pins 52 and 54) also go directly to IC143 (pins 2 and 3).

System Control Microprocessors

There are 3 microprocessors on the Input Board, the main, the sub and the USB micro. The latter is also kept separate in order to perform upgrades over USB.

The AVR400’s main system microprocessor IC151 is a Toshiba T5CN5 microcontroller. This has an ARM Cortex 3 core with 512KB of ROM and 32KB of flash memory. It is a 3V3 part, with this power supply being derived from the main 5V supply via the 3-terminal regulator IC156. It has a 40MHz system clock derived from crystal X702 and a real time clock from the 32.768 kHz crystal X708.

IC152 is a 32Kbit EEPROM for retaining system settings at power down.

IC155 is a MOSFET switch to enable the HDMI CEC (Consumer Electronic Control) bus when the unit is powered up, and to isolate the parts of the bus external to the AVR400 when it is powered down.

IC151 has several sets of comms busses - SPI, I2C and UARTs - depending on which system or peripheral ICs are being addressed. SPI (Serial Peripheral Interface) is a fast 3-wire interface (clock, transmit and receive) with chip select being addressed by individual I/Os. I2C (Inter Integrated Circuit) is a relatively slow bidirectional 2-wire interface, with open-collector/source clock and transmit/receive busses, each with a pull up resistor, and a limited number of embedded chip addresses. UART stands for Universal Asynchronous Receiver/Transmitter and is a form of bus that takes bytes of information and turns them into serial data on a bus before reassembling them into bytes at the other end.

SPI is used to talk to the codec IC143 and the two DSPs IC141 and IC142.

I2C is used for both the main and zone 2 volume controls IC101 and IC131. I2C also connects to the sub micro IC154 and to the NJW1321 video input decoders IC81 and IC81.

IC151’s UARTs are used for USB Tx/Rx, the Torino (video processor) Tx/Rx and the external RS232 Tx/Rx.

Further UARTs on the sub micro IC154 communicate with the Venice 6.2 DAB/Ethernet receiver and the iPod external interface. IC154 is a Toshiba M333FWFG ARM Cortex 3 microcontroller with 128K ROM and 8K of flash, effectively used as a helper for IC151. Its 3V3 power supply regulator IC158 runs from the board’s main 5V supply.

The USB micro (“Bolero”) IC162 is a Toshiba TMP92FD28FG, a 32-bit CISC microcontroller with a built-in USB2 host controller capable of supporting 12Mbps. Its primary function is to provide a “bullet-proof” system updating process via an external USB stick. When the AVR400 is powered up IC162 first self boots, then interrogates the rest of the system – if it receives the wrong response (e.g. if a previous update failed part way through) then the unit will appear dead. However IC162 will be constantly inter-