Installation and removal
M ARGHERITA
WhenMargherita arrives
Whether new or just transported to a new house, installation is extremely important for the correct functioning of your washing machine.
After removing the appliance from its packaging, check that it is intact. If in doubt, contact a qualified technician immediately. The inside of the machine is supported,fortransportation,by four screws on the back panel.
Before using the washing machine, remove the screws, remove the spacers together with the rubber tubes attached to them (keeping all the parts) and use the plastic plugs provided to fill in the holes.
Important: Usethecap(provided) to close the 3 holes which housed the stop pin, situated in the right- hand part of the lower back of the washingmachine.
Levelling
The washing machine must be levelled appropriatey in order to guarantee its correct functioning. To level the appliance, the front feet must be adjusted; the angle ofinclination,measuredaccording to the worktop, must not exceed 2°. When placed on carpet, make suretheventilationisnotreduced.
Connection to the water mains
Both hot and cold water supplies are preferable and they should be between 34.5kN/m²(5lb/in²) and 1034.2kN/m² (150lb/in²) pressure. Thehosehavingtheredendfitting should be encountered between the hot supply and the threaded connection adjacent to the letter H on the rear of the machine. The hosehavingthe whiteendfittings shouldbeconnectedbetweenthe cold supply and the threaded connection adjacent to the letter C on the rear of the machine. Remember to insert a sealing washer at each connection to ensure watertight joints. Do not overtighten the connections by
Note:themaximumtemperature should not exceed 70°C (158°F).
Connecting the drain hose
The drain hose (hooked pipe) is securedtotherearofthemachine by support clips and may be routed to right or left as required.
The hook to be used in case the drain hose ends at a height below 60 cm.
The drain hose should be placed in a stand pipe with a minimum internal diameter of 38 mm (1½ inches) or it can be positioned over a sink or it can be connected as shown in Fig. A. The height of stand pipe or sink should be between 60 and 100 cm (24 and 40 inches). Care must be taken that the hose is not obstructed, twisted, submerged or kinked. If the hose is connected with an airtight joining, provision should be made to prevent syphoning.
Electric connection
Your appliance is now supplied with a 13 amp fused plug it can be plugged into a 13 amp socket for immediate use. Before using the appliance please read the instructions below.
WARNING - THIS APPLIANCE MUST BE EARTHED.
THEFOLLOWINGOPERATIONS SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA approved fuse to BS 1362 should always be used, and the fuse cover
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of the correct colour as indicated by the coloured marking or the colour that is embossed in words on the base of the plug. Replacements can be obtained directly from your nearest Service Depot.
The front feet are adjustable.
Retain the transit screws,
spacers and washers. Should you move house then these should be replaced to support the inside of the machine to prevent damage when transporting the machine.
The rubber gasket. |
|
| |
Connect the inlet hose to the |
| Warning! | |
threaded connector on the |
| ||
The company denies | |||
machine rear. | |||
all | liability if and | ||
The guide for draining into tubs and | |||
when these norms are | |||
sinks. | not respected. | ||
| Plastic bags, | ||
| expanded styrofoam, | ||
| nails and other | ||
| packaging parts are | ||
| not | children’s toys, | |
Water pipe inlet at the top right. | and | are potentially | |
|
| dangerous. | |
Fig. A
Margherita - Iinstructions for installation and use 10
