OVERFILL PROTECTION
Your ASKO dishwasher has an overfill protection device that automatically shuts off the inlet valve and circulation pump and starts the drain pump if the water level in the unit should rise above the normal level. If this happens, turn the water off at the main supply and call for service.
ENERGY SAVING TIPS
♦If you plan to wash the dishes right away, there’s no need to
♦Wash only full loads.
♦Use the Auto Wash program whenever possible.
♦Use the Heavy Wash program only for heavily soiled dishes.
♦Don’t use temperatures above 130°F for lightly soiled dishes.
If there is water in the base pan due to an overfill or small leak, the water must be removed before the dishwasher will start.
When an overfill is detected, the display window will show a fault message. (See “Fault Codes” on page 8.)
♦Select the upper or lower basket program or option when only one basket is loaded.
♦Use the Express option when washing only slightly soiled loads.
♦Use the “Short” drying option. (You can speed up the drying process by opening the door slightly to release the moist air.)
SOLUTIONS TO COMMON DISHWASHING PROBLEMS
As with any new appliance, it sometimes takes using it a few times to learn to operate it properly. If you are having minor performance problems with your dishwasher, read this section before calling for service. It may save you time and unnecessary expense.
NOTE: ASKO has no control over what is put in our appliances once installed in a customer’s home. You are solely responsible for what you wash in your ASKO dishwasher.
Poor washing performance
♦The dishes may not be loaded properly. Make sure that soiled surfaces are facing downward or toward the center of the dishwasher. Also, make sure that the bowls, pots, etc., are not stacked so closely that water can’t reach the soiled surfaces.
♦Make sure you are using the appropriate program settings for the dirtiness of your dishes.
♦An item may be obstructing the spray arm rotation. With the baskets loaded and in place, manually turn the spray arms to make sure they move freely.
♦Your dishwasher detergent should be fresh and stored tightly closed in a cool, dry place. Old or caked detergent will not dissolve properly. Wait until you are ready to start the dishwasher to add the detergent. If you are using the Delay program, make sure the dispenser is dry before adding the detergent.
♦Your dishwasher detergent may be inferior. Try a different brand.
♦Make sure the rinse aid dispenser is filled. (See page 6.)
♦If you have hard water in your area, try adding more detergent and increasing the amount of rinse aid dispensed. (See page 5.)
♦Check that the spray arm jets are not clogged.
♦Do not overload the dishes and be careful to avoid nesting.
Poor drying performance
♦Select the Extra Dry setting.
♦If you don’t want to use Extra Dry, you can decrease the drying time by opening the door slightly to let out the warm, humid air.
♦Make sure the rinse aid dispenser is filled. (See page 6.)
♦Make sure you use the proper amount of rinse aid. (See page 6.)
♦Load items with concave bottoms tilted so as much water as possible will run off.
♦Unload the bottom basket first to avoid spilling water onto the dishes when unloading the top basket.
♦Certain plastics may need to be towel dried.
Plastic items
♦Always check the manufacturer’s suggested care instructions before washing plastic in your dishwasher.
♦Some
♦Plastic items dry poorly and may need to be towel dried.
Chipped or Broken Dishes
♦When you load the dishes, be sure they’re securely in place and will not fall over or strike against each other during the wash.
♦Load glasses between the tines, not straddling them.
♦Move the baskets in and out slowly to avoid slamming the dishes together.
♦Make sure not to load dishes so high that the spray arms could strike them.
♦Make sure tall glasses and stemware will clear the top of the tub when you push the basket in.
♦Always load delicate items in the top basket.
♦Do not overload the dishwasher.
♦Do not jam the glasses together when loading.
Continued on next page.
Page 11
